应《网络安全法》要求，自2017年10月1日起，未进行实名认证将不得使用互联网跟帖服务。为保障您的帐号能够正常使用，请尽快对帐号进行手机号验证，感谢您的理解与支持！

24小时热门版块排行榜    

小木虫论坛-学术科研互动平台 » 材料区 » 金属 » 交流互助 » 【求助】镁合金轧制方向
51/1返回列表
查看: 1517  |  回复: 4
只看楼主 @他人 存档 新回复提醒 (忽略) 收藏    在APP中查看
当前只显示满足指定条件的回帖，点击这里查看本话题的所有回帖

caiwangtan

金虫 (正式写手)

[交流] 【求助】镁合金轧制方向

镁合金的轧制方向对力学性能影响大不大？ 也就是说平行于轧制方向和垂直于轧制方向对焊接后抗拉强度影响大不大？谢谢
回复此楼

» 猜你喜欢

» 本主题相关价值贴推荐，对您同样有帮助:

» 抢金币啦！回帖就可以得到:

查看全部散金贴
1楼 2010-11-15 13:14:16
已阅   回复此楼   关注TA 给TA发消息 送TA红花 TA的回帖

lvfengimr

至尊木虫 (著名写手)
caiwangtan(金币+2):谢谢 2010-11-25 11:30:38
有影响  一般横向性能优于轧向
赞一下 回复此楼
3楼2010-11-16 08:03:36
已阅   回复此楼   关注TA 给TA发消息 送TA红花 TA的回帖
查看全部 5 个回答

国产科比

木虫 (著名写手)
caiwangtan(金币+2):谢谢 2010-11-25 11:27:23
不大，起码拉伸性能影响不大，我实验过
赞一下 回复此楼
2楼2010-11-15 21:06:37
已阅   回复此楼   关注TA 给TA发消息 送TA红花 TA的回帖

金教授

新虫 (小有名气)
引用回帖:
Originally posted by caiwangtan at 2010-11-15 13:14:16:
镁合金的轧制方向对力学性能影响大不大？ 也就是说平行于轧制方向和垂直于轧制方向对焊接后抗拉强度影响大不大？谢谢

Magnesium alloys have strong planar anisotropy, e.g., the tensile properties in 0, 45 and 90 deg to RD are very different. This is due to the fact that magnesium alloys usually have h.c.p. structure. Generally speaking, the lower the symmetry of lattice unit, the higher the anisotropy. For example, h.c.p. magnesium has much stronger anisotropy than f.c.c. aluminum. The strong anisotropy in magnesium alloys can be explained by (i) the texture, (ii) slip system and (iii) Schmid factor.

The texture in magnesium sheets is mainly the basal texture {0001}<11-20>. During deformation, there are 4 possible slip systems:

(1)        Basal {0001}<11-20>
(2)        Prismatic {10-10}<11-20>
(3)        Pyramidal {11-22}<11-2-3> + {10-12}<11-20>
(4)        Twinning <10-11> on {10-12}

At elevated temperature, it is more complex because grain boundary sliding is involved. When you calculate the Schmid factors at different directions, you will see that tensile at 45 deg to RD is the easiest, and tensile at 0 deg is slightly easier than at 90 deg. Therefore, it is often observed that YS-45 < YS-0 < YS-90 and EL-45 > EL-0 > EL-90. However, it is also dependent on the chemical composition, the temper (as-rolled or fully annealed), the grain size, the forming temperature and many other factors. Sometimes the difference between the 0 deg and 90 deg is not very obvious, and it may also be reverse in some alloys under certain conditions, i.e., YS-0 > YS-90 and EL-0 < EL-90.

[ Last edited by 金教授 on 2010-11-16 at 10:52 ]
赞一下 回复此楼
4楼2010-11-16 10:50:42
已阅   回复此楼   关注TA 给TA发消息 送TA红花 TA的回帖

jdxq

木虫 (著名写手)
对于镁合金，细晶强化不能是深冲性能提高，反而降低了！
赞一下 回复此楼
5楼2013-03-07 09:39:07
已阅   回复此楼   关注TA 给TA发消息 送TA红花 TA的回帖
查看全部 5 个回答
普通表情 龙 兔 虎 猫 高级回复 (可上传附件)
信息提示
关闭
请填处理意见
关闭