| 查看: 1625 | 回复: 4 | |||
[交流]
【求助】镁合金轧制方向
|
| 镁合金的轧制方向对力学性能影响大不大？ 也就是说平行于轧制方向和垂直于轧制方向对焊接后抗拉强度影响大不大？谢谢 |
回复此楼» 猜你喜欢
售SCI文章，我:8O.5.5.1O.54,科目全,可十急
已经有4人回复
-
售SCI一区T0P文章，我:8.O.55.1.O54,科目全,可伽急
已经有4人回复
-
售SCI一区文章，我:8.O.55.1.O.54,科目齐全,可伽急
已经有4人回复
-
售SCI一区T0P文章，我:8.O.55.1.O.54,科目齐全,可+急
已经有4人回复
-
售SCI-T0P文章，我:8O.5.5.1.O.54,科目齐全,可+急
已经有3人回复
-
售SCI文章，我:8O.5.5.1O.54,科目全,可十急
已经有3人回复
-
售一区SCI文章T0P，我:8O.551.O54,科目全,可十急
已经有3人回复
-
售SCI文章，我:8O5.5.1.O.54,科目齐全,可+急
已经有4人回复
-
售SCI文章，我:8O5.5.1.O.54,科目齐全,可+急
已经有3人回复
-
售SCI一区T0P文章，我:8.O.55.1.O54,科目全,可伽急
已经有3人回复
» 本主题相关价值贴推荐，对您同样有帮助:
- 有条件织构消除，集思广益
已经有15人回复
- 轧制退火后成长条状
已经有32人回复
- 【讨论】新的一年，新的金属版，版块大改革，期待您参与
已经有28人回复
- 【求助】金属材料的极图代表什么意思？怎么分析？
已经有18人回复
- 【讨论】为啥垂直轧向的强度高于轧制方向呢？
已经有7人回复
- 【求助】关于金属力学性能各向异性的问题，谢谢
已经有15人回复
- 【求助】EBSD处理schmid 因子
已经有15人回复
2楼2010-11-15 21:06:37
3楼2010-11-16 08:03:36
|
Magnesium alloys have strong planar anisotropy, e.g., the tensile properties in 0, 45 and 90 deg to RD are very different. This is due to the fact that magnesium alloys usually have h.c.p. structure. Generally speaking, the lower the symmetry of lattice unit, the higher the anisotropy. For example, h.c.p. magnesium has much stronger anisotropy than f.c.c. aluminum. The strong anisotropy in magnesium alloys can be explained by (i) the texture, (ii) slip system and (iii) Schmid factor. The texture in magnesium sheets is mainly the basal texture {0001}<11-20>. During deformation, there are 4 possible slip systems: (1) Basal {0001}<11-20> (2) Prismatic {10-10}<11-20> (3) Pyramidal {11-22}<11-2-3> + {10-12}<11-20> (4) Twinning <10-11> on {10-12} At elevated temperature, it is more complex because grain boundary sliding is involved. When you calculate the Schmid factors at different directions, you will see that tensile at 45 deg to RD is the easiest, and tensile at 0 deg is slightly easier than at 90 deg. Therefore, it is often observed that YS-45 < YS-0 < YS-90 and EL-45 > EL-0 > EL-90. However, it is also dependent on the chemical composition, the temper (as-rolled or fully annealed), the grain size, the forming temperature and many other factors. Sometimes the difference between the 0 deg and 90 deg is not very obvious, and it may also be reverse in some alloys under certain conditions, i.e., YS-0 > YS-90 and EL-0 < EL-90. [ Last edited by 金教授 on 2010-11-16 at 10:52 ] |
4楼2010-11-16 10:50:42
5楼2013-03-07 09:39:07
