| 查看: 1268 | 回复: 4 | |||
| 当前主题已经存档。 | |||
| 当前只显示满足指定条件的回帖，点击这里查看本话题的所有回帖 | |||
[交流]
[请教]用液氮和丙酮配混合溶液用来至冷的比例！
|
|||
| 准备做化学吸附，需要－85摄氏度。文献上用液氮和丙酮配混合溶液来达到该要求，请问大牛：什么样的比例能达到零下85度啊！谢谢。 |
回复此楼» 猜你喜欢
关于合成MIL-125的求助
已经有0人回复
-
双非本硕光催化方向想读博，请各位老师看看我！
已经有2人回复
-
化学工程及工业化学论文润色/翻译怎么收费?
已经有107人回复
-
瑞典林雪平大学范立洲课题组现招聘博士后、岗位制博士生
已经有0人回复
-
中国科大仿生界面材料科学全国重点实验室戴懿涛研究员/江雷院士团队招聘科研助理
已经有0人回复
-
中国科大仿生界面材料科学全国重点实验室戴懿涛研究员/江雷院士团队招聘科研助理
已经有0人回复
-
寻求物理化学学报最新的投稿模板！
已经有4人回复
-
东南大学杰青/海优团队招聘催化方向博士后
已经有866人回复
-
投稿咨询
已经有7人回复
-
自科面上 散金币 祈福
已经有61人回复
-
铁钼催化剂成型
已经有2人回复
zhangwengui330
荣誉版主 (职业作家)
- C-EPI: 1
- 应助: 203 (大学生)
- 贵宾: 2.215
- 金币: 21820.1
- 红花: 48
- 帖子: 4420
- 在线: 866.4小时
- 虫号: 309984
- 注册: 2006-12-23
- 性别: GG
- 专业: 催化化学
- 管辖: 催化
3楼2008-10-25 17:48:22
2楼2008-10-24 08:54:04
IPA/LN2
★
^_^@^_^(金币+1,VIP+0):QQQ
^_^@^_^(金币+1,VIP+0):QQQ
|
An isopropyl alcohol (IPA)/liquid nitrogen (LN2) slurry is used to maintain cold trap temperatures of approximately -80 °C. Use the following instructions to mix such a slurry if this is the temperature you wish to maintain. 1.Chill a 600-mL dewar by rinsing it with LN2. Allow a small amount of LN2 to remain in the bottom of the dewar (approximately 1 cm deep). 2.Stirring constantly, slowly add approximately 500 mL of IPA. For greatest safety, use a laboratory squirt bottle. Squirt the stream of IPA along the inside edge of the dewar, very near the top, allowing the IPA to flow down the dewar’s inside wall. Do not stop stirring the mixture in the bottom of the dewar, even if stirring becomes difficult. As you continue stirring and adding IPA, the mixture will loosen and become easier to stir. 3.When all the IPA has been placed in the dewar, slowly begin pouring LN2 into the dewar. Approximately 1 liter is needed. You must continuously stir the mixture as you add the LN2. As ice chunks form, break them up and stir them down into the mixture. Avoid splashing. Gently knock ice chunks away from the sides of the dewar and continue stirring. Add liquid nitrogen until the slurry is within 25 mm (1 in.) of the top of the dewar. 4.Lift the stirrer out of the slurry and observe as the slurry drips into the dewar; the stirrer should be thickly coated with slurry. Your goal is to achieve a slurry that has a thick, syrupy consistency without large chunks. When the slurry is cold enough, small pieces of ice may be present (10 - 20% of the mixture). A little ice accumulation along the sides of the dewar is acceptable. |
4楼2008-11-20 17:08:11
amorphous
铁杆木虫 (著名写手)
小木虫之超级奶爸
- 应助: 7 (幼儿园)
- 贵宾: 0.15
- 金币: 8620.8
- 红花: 1
- 帖子: 1290
- 在线: 160.1小时
- 虫号: 431986
- 注册: 2007-08-12
- 专业: 催化化学
5楼2008-11-21 08:24:29
30