| 查看: 985 | 回复: 4 | |||
| 当前主题已经存档。 | |||
[交流]
[请教]用液氮和丙酮配混合溶液用来至冷的比例！
|
|||
| 准备做化学吸附，需要－85摄氏度。文献上用液氮和丙酮配混合溶液来达到该要求，请问大牛：什么样的比例能达到零下85度啊！谢谢。 |
回复此楼» 猜你喜欢
中国水产科学研究院黄海水产研究所博士后科研工作站2026年博士后招收公告
已经有0人回复
-
大连海事大学国家级人才团队2026年博士研究生招生启事（氢能）
已经有10人回复
-
化学工程及工业化学论文润色/翻译怎么收费?
已经有175人回复
-
国家级人才课题组招收2026年入学博士
已经有6人回复
-
意大利米兰理工大学急聘CSC公派留学博士生（物理或无机材料科学方向）
已经有41人回复
-
求加氢处理工艺与工程（第二版）pdf 李大东 中国石化出版社 9787511436689
已经有0人回复
-
新加坡ASTAR招收CSC或学校资助联培博士生/访问学生
已经有1人回复
-
求助Amsterdam Density Functional
已经有0人回复
-
Postdoctoral Research Fellow Position in Causal Inference Weill CorneIl Medicine
已经有0人回复
-
武汉纺织大学全国重点实验室陈嵘教授团队招收2026级学术/专业型硕士研究生
已经有0人回复
2楼2008-10-24 08:54:04
zhangwengui330
荣誉版主 (职业作家)
- C-EPI: 1
- 应助: 203 (大学生)
- 贵宾: 2.215
- 金币: 21820.1
- 红花: 48
- 帖子: 4420
- 在线: 866.4小时
- 虫号: 309984
- 注册: 2006-12-23
- 性别: GG
- 专业: 催化化学
- 管辖: 催化
3楼2008-10-25 17:48:22
IPA/LN2
★
^_^@^_^(金币+1,VIP+0):QQQ
^_^@^_^(金币+1,VIP+0):QQQ
|
An isopropyl alcohol (IPA)/liquid nitrogen (LN2) slurry is used to maintain cold trap temperatures of approximately -80 °C. Use the following instructions to mix such a slurry if this is the temperature you wish to maintain. 1.Chill a 600-mL dewar by rinsing it with LN2. Allow a small amount of LN2 to remain in the bottom of the dewar (approximately 1 cm deep). 2.Stirring constantly, slowly add approximately 500 mL of IPA. For greatest safety, use a laboratory squirt bottle. Squirt the stream of IPA along the inside edge of the dewar, very near the top, allowing the IPA to flow down the dewar’s inside wall. Do not stop stirring the mixture in the bottom of the dewar, even if stirring becomes difficult. As you continue stirring and adding IPA, the mixture will loosen and become easier to stir. 3.When all the IPA has been placed in the dewar, slowly begin pouring LN2 into the dewar. Approximately 1 liter is needed. You must continuously stir the mixture as you add the LN2. As ice chunks form, break them up and stir them down into the mixture. Avoid splashing. Gently knock ice chunks away from the sides of the dewar and continue stirring. Add liquid nitrogen until the slurry is within 25 mm (1 in.) of the top of the dewar. 4.Lift the stirrer out of the slurry and observe as the slurry drips into the dewar; the stirrer should be thickly coated with slurry. Your goal is to achieve a slurry that has a thick, syrupy consistency without large chunks. When the slurry is cold enough, small pieces of ice may be present (10 - 20% of the mixture). A little ice accumulation along the sides of the dewar is acceptable. |
4楼2008-11-20 17:08:11
amorphous
铁杆木虫 (著名写手)
小木虫之超级奶爸
- 应助: 7 (幼儿园)
- 贵宾: 0.15
- 金币: 8594.3
- 红花: 1
- 帖子: 1290
- 在线: 160.1小时
- 虫号: 431986
- 注册: 2007-08-12
- 专业: 催化化学
5楼2008-11-21 08:24:29