| 查看: 2168 | 回复: 9 | |||
[求助]
求大神指点翻译此ANSYS命令的意思？本人是菜鸟，还望大神说明白点。 已有3人参与
|
|
finish /clear /filname,CCNBD /prep7 et,1,solid95 et,2,plane82 mp,ex,1,17.67e9 mp,prxy,1,0.21 mp,dens,1,3055 step=1340 ho=0.056 !试样厚度 不是这个试样的几何参数 p=0.1477 !试样直径 q=0.48 !无量纲裂纹长度 Am=0.5*p*q !临界裂纹长度 xm=0.5*ho+0.0135-sqrt(0.0485*0.0485-Am*Am) !裂纹前沿宽度 cyl4,,,,,p/2,90,ho/2 !kdist,p block,,0.03,,0.06,,xm !15.2裂纹前沿宽度 block,,0.03,,0.06,xm,ho/2 vplot /pnum,volu,1 !HELP,VOVLAP block,,0.014,0.024,0.054,0,ho/2 vovlap,all wprota,,,90 cyl4,-1/2*ho-0.0135,,0.0485,360 adele,1 lplot /pnum,line,1 ldele,2,,,1 ldele,5,6,1,1 lovlap,1,48 !lsel,s,p !HELP,LOVLAP ldele,2,,,1 ldele,6,,,1 ldele,9,,,1 /pnum,kp,1 lang,34,16,90 wpcsys,-1,0 kwpave,8 cyl4,,,0.004,-90,,90 vdrag,1,,,,,,2,5 vplot lplot !ksel,s,p kwpave,22 !vplo vsbw,2 vdele,4,,,1 ldele,5,,,1 !lplot !lovlap,42,9 !ldele,31,,,1 !ldele,26,,,1 !ldele,29,,,1 !lsel,s,p !ldele,2,,,1 !lsel,s,p !ldele,30,,,1 !lsel,s,p vplot vovlap,all kplot lplot !ksel,s,p ldele,2,,,1 aplot lsel,s,loc,z,0 lplot lesize,67,,,2,,,,,1 lesize,35,,,4,,,,,1 lesize,11,,,9,,,,,1 lesize,69,,,8,,,,,1 lesize,37,,,4,,,,,1 lesize,36,,,8,,,,,1 lesize,12,,,18,,,,,1 lesize,65,,,8,,,,,1 mshkey,0 mshape,0,2d aplot !amesh,42 !mshkey,0 amesh,42 aplot allsel lesize,21,,,4,,,,,1 !vsel,s,p vsweep,8 allsel aplot lesize,60,,,8,,,,,1 lplot vplot !vsel,s,p vsweep,9 aplot lsel,s,loc,z,0 lplot !lesize,62,,,3,,,,,1 !lesize,62,,,4,,,,,1 !lesize,62,,,4,,,,,0.25 !lesize,62,,,4,0.25,,,,1 !lesize,62,,,3,0.25,,,,1 lesize,62,,,3,,,,,1 lesize,3,,,24,,,,,1 !lesize,3,,,18,,,,,1 !lesize,61,,,10,0.25,,,,1 lesize,61,,,10,,,,,1 apot aplot lplot mshkey,0 mshape,0,2d aplot amesh,35 !aclear,35 lplot allsel vsweep,7 !elist vplot lplot lesize,9,,,8,0.25,,,,1 lesize,10,,,8,4,,,,1 lesize,6,,,12,,,,,1 allsel kscon,19,0.004/15,1,8,1 amesh,1 lesize,23,,,18,,,,,1 lesize,75,,,30,,,,,1 vsweep,2 lplot vsweep,4 mshkey,0 mshape,1,3d esize,0.003 vmesh,10 vmesh,11 esel,s,type,,2 aclear,all allsel,all numcmp,all aplot wpcsys,-1,0 /pnum,area,1 vsymm,y,all,,,,0,0 !镜像产生网格 eplot aplot asel,s,loc,y,0 !kplot !ksel,s,loc,y,0 !nummrg,kp allsel allsel nsel,s,loc,y,0 nplot /pnum,node,1 nummrg,node allsel aplot kplot ksel,s,loc,y,0 nummrg,kp kplot lplot lsel,s,loc,y,0 !lsel,s,p aplot asel,s,loc,y,0 allsel eplot /pnum,node,0 numcmp,all lsel,s,,,5 NSLL,S,1 !耦合Y方向位移 nplot cp,1,uy,all allsel aplot lsel,s,,,92 NSLL,S,1 !耦合Y方向位移 nplot cp,2,uy,all dl,92,,uy asel,s,loc,z,0 DA,ALL,symm allsel,all asel,s,,,18,38,20 asel,a,,,12,42,30 asel,a,,,51,61,10 asel,a,,,3,73,70 !施加面对称约束 asel,a,,,29,32,3 asel,a,,,66,77,11 asel,a,,,14,48,34 da,all,symm /PNUM,NODE,0 allsel /solu !求解 antype,trans trnopt,full outr,all,all *dim,LF,array,step !/input,G:\fanhong\21\21,txt !50点光滑荷载 /input,E:\E\HEZAI\21,txt *do,i,5,step,5 !节点上施加集中荷载 lsel,s,,,5 nsll,s,1 kbc,0 f,all,fy,-LF(i)/(25*4) !1/4荷载，1/8模型 time,i*1e-7 !lswrite,i allsel solve *enddo !lssolve,1,step,1 finish save /post1 d=distnd(15967,15983) pi=acos(-1) co=sqrt(2*pi)*17.67e9/(24*(1-0.21*0.21)*sqrt(d))/1e6 !系数改 /post26 numvar,200 nsol,2,15983,u,x !uB(t) m 原点15967 nsol,3,15984,u,x !uA(t) add,4,2,3,,,,,8,-1 !8*uB(t)-uA(t) add,5,4,,,K1,,,co !K1 lines,20000 pi=acos(-1) b=17232 a=17214 p=2 !求解原点16836到16850 q=3 s=4 k=5 *do,m,16836,16850,2 !m原点 d=distnd(b,m) co=sqrt(2*pi)*17.67e9/(24*(1-0.21*0.21)*sqrt(d))/1e6 !系数改 nsol,p,b,u,x !uB(t) b 原点14692 变量用p2 nsol,q,a,u,x !uA(t) a q3 add,s,p,q,,,,,8,-1 !8*uB(t)-uA(t) s4 add,k,s,,,,,,co !K1 k5 p=p+4 q=q+4 s=s+4 k=k+4 b=b-1 a=a-2 *enddo !pi=acos(-1) !b=15598 !a=15597 !p=2 !求解原点17884到17900 !q=3 !s=4 !k=5 *do,m,17884,17900,2 !m原点 d=distnd(b,m) co=sqrt(2*pi)*17.67e9/(24*(1-0.21*0.21)*sqrt(d))/1e6 !系数改 nsol,p,b,u,x !uB(t) b 原点14692 变量用p2 nsol,q,a,u,x !uA(t) a q3 add,s,p,q,,,,,8,-1 !8*uB(t)-uA(t) s4 add,k,s,,,,,,co !K1 k5 p=p+4 q=q+4 s=s+4 k=k+4 b=b-1 a=a-2 *enddo d=distnd(16834,17233) !求解16834 !pi=acos(-1) co=sqrt(2*pi)*17.67e9/(24*(1-0.21*0.21)*sqrt(d))/1e6 !系数改 !/post26 nsol,2,17233,u,x !uB(t) m nsol,3,17234,u,x !uA(t) add,4,2,3,,,,,8,-1 !8*uB(t)-uA(t) add,5,4,,,K1,,,co !K1 lines,20000 d61=distnd(15561,15957) !原点15561 co61=sqrt(2*pi)*17.67e9/(24*(1-0.21*0.21)*sqrt(d61))/1e6 !系数改 nsol,2,15957,u,x !uB(t) nsol,3,15939,u,x !uA(t) add,4,2,3,,,,,8,-1 !8*uB(t)-uA(t) add,5,4,,,K1,,,co61 !K1 lines,20000 d63=distnd(15563,15956) !原点15563 co63=sqrt(2*pi)*17.67e9/(24*(1-0.21*0.21)*sqrt(d63))/1e6 !系数改 nsol,2,15956,u,x !uB(t) nsol,3,15937,u,x !uA(t) add,4,2,3,,,,,8,-1 !8*uB(t)-uA(t) add,5,4,,,K1,,,co63 !K1 lines,20000 d65=distnd(15565,15955) !原点15565 co65=sqrt(2*pi)*17.67e9/(24*(1-0.21*0.21)*sqrt(d65))/1e6 !系数改 nsol,2,15955,u,x !uB(t) nsol,3,15935,u,x !uA(t) add,4,2,3,,,,,8,-1 !8*uB(t)-uA(t) add,5,4,,,K1,,,co65 !K1 lines,20000 d67=distnd(15567,15954) !原点15567 co67=sqrt(2*pi)*17.67e9/(24*(1-0.21*0.21)*sqrt(d67))/1e6 !系数改 nsol,2,15954,u,x !uB(t) nsol,3,15933,u,x !uA(t) add,4,2,3,,,,,8,-1 !8*uB(t)-uA(t) add,5,4,,,K1,,,co67 !K1 lines,20000 d69=distnd(15569,15953) !原点15569 co69=sqrt(2*pi)*17.67e9/(24*(1-0.21*0.21)*sqrt(d69))/1e6 !系数改 nsol,2,15953,u,x !uB(t) nsol,3,15931,u,x !uA(t) add,4,2,3,,,,,8,-1 !8*uB(t)-uA(t) add,5,4,,,K1,,,co69 !K1 lines,20000 d71=distnd(15571,15952) !原点15571 co71=sqrt(2*pi)*17.67e9/(24*(1-0.21*0.21)*sqrt(d71))/1e6 !系数改 nsol,2,15952,u,x !uB(t) nsol,3,15929,u,x !uA(t) add,4,2,3,,,,,8,-1 !8*uB(t)-uA(t) add,5,4,,,K1,,,co71 !K1 lines,20000 d73=distnd(15573,15951) !原点15573 co73=sqrt(2*pi)*17.67e9/(24*(1-0.21*0.21)*sqrt(d73))/1e6 !系数改 nsol,2,15951,u,x !uB(t) nsol,3,15927,u,x !uA(t) add,4,2,3,,,,,8,-1 !8*uB(t)-uA(t) add,5,4,,,K1,,,co73 !K1 lines,20000 d75=distnd(15575,15950) !原点15575 co75=sqrt(2*pi)*17.67e9/(24*(1-0.21*0.21)*sqrt(d75))/1e6 !系数改 nsol,2,15950,u,x !uB(t) nsol,3,15925,u,x !uA(t) add,4,2,3,,,,,8,-1 !8*uB(t)-uA(t) add,5,4,,,K1,,,co75 !K1 lines,20000 d09=distnd(16609,15949) !原点16609 co09=sqrt(2*pi)*17.67e9/(24*(1-0.21*0.21)*sqrt(d09))/1e6 !系数改 nsol,2,15949,u,x !uB(t) nsol,3,15923,u,x !uA(t) add,4,2,3,,,,,8,-1 !8*uB(t)-uA(t) add,5,4,,,K1,,,co09 !K1 lines,20000 d11=distnd(16611,15948) !原点16611 co11=sqrt(2*pi)*17.67e9/(24*(1-0.21*0.21)*sqrt(d11))/1e6 !系数改 nsol,2,15948,u,x !uB(t) nsol,3,15921,u,x !uA(t) add,4,2,3,,,,,8,-1 !8*uB(t)-uA(t) add,5,4,,,K1,,,co11 !K1 lines,20000 d13=distnd(16613,15947) !原点16613 co13=sqrt(2*pi)*17.67e9/(24*(1-0.21*0.21)*sqrt(d13))/1e6 !系数改 nsol,2,15947,u,x !uB(t) nsol,3,15919,u,x !uA(t) add,4,2,3,,,,,8,-1 !8*uB(t)-uA(t) add,5,4,,,K1,,,co13 !K1 lines,20000 d15=distnd(16615,15946) !原点16615 co15=sqrt(2*pi)*17.67e9/(24*(1-0.21*0.21)*sqrt(d15))/1e6 !系数改 nsol,2,15946,u,x !uB(t) nsol,3,15917,u,x !uA(t) add,4,2,3,,,,,8,-1 !8*uB(t)-uA(t) add,5,4,,,K1,,,co15 !K1 lines,20000 d17=distnd(16617,15945) !原点16617 co17=sqrt(2*pi)*17.67e9/(24*(1-0.21*0.21)*sqrt(d17))/1e6 !系数改 nsol,2,15945,u,x !uB(t) nsol,3,15915,u,x !uA(t) add,4,2,3,,,,,8,-1 !8*uB(t)-uA(t) add,5,4,,,K1,,,co17 !K1 lines,20000 d19=distnd(16619,15944) !原点16619 co19=sqrt(2*pi)*17.67e9/(24*(1-0.21*0.21)*sqrt(d19))/1e6 !系数改 nsol,2,15944,u,x !uB(t) nsol,3,15913,u,x !uA(t) add,4,2,3,,,,,8,-1 !8*uB(t)-uA(t) add,5,4,,,K1,,,co19 !K1 lines,20000 d21=distnd(16621,15943) !原点16621 co21=sqrt(2*pi)*17.67e9/(24*(1-0.21*0.21)*sqrt(d21))/1e6 !系数改 nsol,2,15943,u,x !uB(t) nsol,3,15911,u,x !uA(t) add,4,2,3,,,,,8,-1 !8*uB(t)-uA(t) add,5,4,,,K1,,,co21 !K1 lines,20000 d23=distnd(16623,15942) !原点16623 co23=sqrt(2*pi)*17.67e9/(24*(1-0.21*0.21)*sqrt(d23))/1e6 !系数改 nsol,2,15942,u,x !uB(t) nsol,3,15909,u,x !uA(t) add,4,2,3,,,,,8,-1 !8*uB(t)-uA(t) add,5,4,,,K1,,,co23 !K1 lines,20000 d25=distnd(16625,15941) !原点16625 co25=sqrt(2*pi)*17.67e9/(24*(1-0.21*0.21)*sqrt(d25))/1e6 !系数改 nsol,2,15941,u,x !uB(t) nsol,3,15907,u,x !uA(t) add,4,2,3,,,,,8,-1 !8*uB(t)-uA(t) add,5,4,,,K1,,,co25 !K1 lines,20000 d59=distnd(15559,15958) !原点15559 co59=sqrt(2*pi)*17.67e9/(24*(1-0.21*0.21)*sqrt(d59))/1e6 !系数改 nsol,2,15958,u,x !uB(t) nsol,3,15959,u,x !uA(t) add,4,2,3,,,,,8,-1 !8*uB(t)-uA(t) add,5,4,,,K1,,,co59 !K1 lines,20000 /post1 cs,15,0,14692,14707,14807 !i为局部坐标系11的原点 csys,15 RSYS,15 PATH,i,3 PPATH,1,14692 ppath,2,14708 ppath,3,14709 KCALC,,,1,1 |
回复此楼» 猜你喜欢
今天系统多次维护，明天很可能放榜！
已经有5人回复
-
欢迎发来filecode的Mz6后的代码验证其规律
已经有74人回复
-
岩土工程学报什么时候才能终审完呐
已经有4人回复
-
时间戳又变了8-15
已经有25人回复
-
2027广东省杰青
已经有6人回复
-
快农历七夕节了，轻松一下，男人悄悄话，女施主请不要进来。
已经有3人回复
-
哪位老哥知道今年的国自然具体哪一天放榜？
已经有9人回复
-
咱们一起用铁证分析2026国家社科基金中标与否
已经有26人回复
-
我的国基提前知道中了，可是同事的操作让我实在接受不了，怎么会有这样的人
已经有16人回复
-
有时候，自然基金真的不能太认真 （我的申报经验）
已经有12人回复
» 本主题相关价值贴推荐，对您同样有帮助:
- 关于精密度、回收率的问题，求大神帮帮我
已经有6人回复
- 求哪位大神给发一个ansys求解箱梁剪力滞效应的命令流，小弟新手，不知道如何下手
已经有5人回复
- 新手求教 如何提高AnsysMeshing网格质量问题 求大神指点。
已经有7人回复
- 关于ANSYS荷载组合问题，求大神指点迷津！！
已经有4人回复
- 菜鸟求助，老师给了一个分子让优化，可总是错误，求大神指点
已经有22人回复
- 求助ansys workbench模块材料库，金币不多但全散，望有的大神分享啊！！
已经有8人回复
- ansys关于GLUE容差的问题，请大神指点
已经有3人回复
- 在ansys中做齿轮瞬态温度场分析，遇到问题，求大神指点
已经有9人回复
凌云1314
金虫 (著名写手)
- 应助: 7 (幼儿园)
- 金币: 4895.7
- 散金: 60
- 红花: 3
- 帖子: 1415
- 在线: 96.3小时
- 虫号: 2747657
- 注册: 2013-10-23
- 性别: GG
- 专业: 工程热物理相关交叉领域
2楼2015-07-02 00:54:22
3楼2015-07-02 08:36:43
shgao20
专家顾问 (职业作家)
-
专家经验: +809 - 仿真EPI: 1
- 应助: 1311 (讲师)
- 金币: 13381.4
- 红花: 267
- 帖子: 3531
- 在线: 473.4小时
- 虫号: 3644138
- 注册: 2015-01-14
- 专业: 动力学与控制
- 管辖: 仿真模拟
4楼2015-07-02 21:14:10
独孤神宇
版主 (知名作家)
- 应助: 490 (硕士)
- 贵宾: 0.008
- 金币: 31016.3
- 散金: 802
- 红花: 122
- 沙发: 1
- 帖子: 5600
- 在线: 856.5小时
- 虫号: 3522474
- 注册: 2014-11-06
- 性别: GG
- 专业: 机械动力学
- 管辖: 计算模拟
5楼2015-07-03 11:00:45
6楼2015-07-04 10:15:13
7楼2015-07-04 11:29:14
8楼2015-07-04 11:38:01
金华岁月
金虫 (著名写手)
- 应助: 6 (幼儿园)
- 金币: 3131.5
- 散金: 423
- 红花: 9
- 帖子: 1527
- 在线: 574.3小时
- 虫号: 2387160
- 注册: 2013-03-29
- 性别: GG
- 专业: 微/纳机械系统
9楼2015-07-04 22:09:25
10楼2015-07-05 14:52:57
25