24小时热门版块排行榜    

CyRhmU.jpeg
查看: 871  |  回复: 3
本帖产生 1 个 翻译EPI ,点击这里进行查看

王灵杰

金虫 (初入文坛)

[求助] 150单词奖励150金币(不够再加 不差钱)

The intensity ratio of the D and G bands (ID/IG) is commonly used to evaluate the quality of carbon materials. No obvious D band was observed for any of the MWCNTs dispersed on substrates (Supplementary Fig. 6), suggesting the high quality of the starting materials. The average ID/IG values were respectively 0.38, 0.30 and 0.28 for our single-, bi- and trilayer GNRs with 10–20-nm widths.Because defect density on the pristine MWCNTs was low, the D-band Raman signal of our GNRs should be mainly due to their open edges24,25. The ID/IG values were lower than those for GNRs obtained by lithographic etching of pristine graphene sheets (ID/IG was ,2 for a bilayer GNR of,28-nm width obtained by lithographic patterning (X. R. Wang et al., unpublished data); see Supplementary Fig. 5),indicating the high quality of our GNRs, in particular the high degree of edge smoothness.
已阅   回复此楼   关注TA 给TA发消息 送TA红花 TA的回帖

8814402

至尊木虫 (职业作家)

【答案】应助回帖

王灵杰(金币+150, 翻译EPI+1): 谢谢! 2011-05-31 11:08:13
The intensity ratio of the D and G bands (ID/IG) is commonly used to evaluate the quality of carbon materials.D带和G带强度比常常用来评价碳材料的质量。 No obvious D band was observed for any of the MWCNTs dispersed on substrates (Supplementary Fig. 6), suggesting the high quality of the starting materials. 对任何分散在基质中的MWCNTs,均未能观测到明显的D带,提示起始原料良好的质量。The average ID/IG values were respectively 0.38, 0.30 and 0.28 for our single-, bi- and trilayer GNRs with 10–20-nm widths. 我们宽度为10-20nm的单、双和三层GNR的平均ID/IG 值分别为0.38、0.30和0.28。 Because defect density on the pristine MWCNTs was low, the D-band Raman signal of our GNRs should be mainly due to their open edges24,25. 由于原始MWCNT的缺陷密度低,所以我们的GNR的D带拉曼信号主要应该是由于它们开放的边缘。The ID/IG values were lower than those for GNRs obtained by lithographic etching of pristine graphene sheets (ID/IG was ,2 for a bilayer GNR of,28-nm width obtained by lithographic patterning (X. R. Wang et al., unpublished data); see Supplementary Fig. 5),indicating the high quality of our GNRs, in particular the high degree of edge smoothness.这些ID/IG值比由平板印刷蚀刻原始石墨烯片之躯的GNR的ID/IG值要低,提示我们的GNR具有较好的质量,尤其具有高度的边缘平衡度。
2楼2011-05-31 09:43:20
已阅   回复此楼   关注TA 给TA发消息 送TA红花 TA的回帖

F074

金虫 (职业作家)

【答案】应助回帖

★ ★
Mally89(金币+2): 感谢应助!~欢迎常来!~ 2011-05-31 12:22:28
D带和G带的强度比通常用来评估含碳材料的质量。从分散的MWCNTs的底物(补充的图表6)上没有发现明显的D带,不能表明原始材料的高质量。平均的ID/IG的比值分别是0.38,0.30,0.28对应于单个的,两个和三个革兰氏阴性菌的10-20纳米的宽度。有缺点的密度在早期的MWCNTs上很低,革兰氏阴性菌的D带的拉曼信号主要归功于它们开放的边缘24,25.革兰氏阴性菌的ID/IG的比值低于这些从原始的石板印刷的已经腐蚀的图表中得到的数据(从图表中获得的ID/IG的比值是2,对于双分子层的革兰氏阴性菌其宽度是28纳米)(X. R. Wang 等未公开的数据);参看补充的图表5),表明我们的革兰氏阴性菌的高质量,部分是高纯度的边缘光滑度。
3楼2011-05-31 09:58:23
已阅   回复此楼   关注TA 给TA发消息 送TA红花 TA的回帖

8814402

至尊木虫 (职业作家)

最末一句应该是“边缘平滑度”。 不好意思
4楼2011-05-31 11:15:29
已阅   回复此楼   关注TA 给TA发消息 送TA红花 TA的回帖
相关版块跳转 我要订阅楼主 王灵杰 的主题更新
信息提示
请填处理意见