| 查看: 401 | 回复: 12 | |||
| 当前主题已经存档。 | |||
guyue_692木虫 (正式写手)
水果总歼
|
[交流]
66金币求助最后几段翻译
|
||
|
更换轴承密封：在端盖上每一个密封点都安装有两个骨架油封，密封装置通常是这样安装的，一个密封面对着物料以隔绝物料与轴承的接触，还有一个密封面对着轴套，以保持润滑油的良好状况，当机器保养时，应对唇形密封进行检查，至少一年一次。拆除密封时，卸掉用螺钉固定在转筒端盖内表面上的固定板，然后拉出两个密封装置和密封隔离环，装进新的密封垫圈和密封件时，确认零件完全对准和无障碍。并与我们提供的机器装配图检验，以确保密封装置的正确安装，一定要确保密封装置在装配过程中不被损坏。 紧急处理：建议转鼓部件在新用的机件至多运转2000小时或一年应进行彻底的检查。前面提到过的临界范围的目测检查和螺栓连结的仔细检查都是必要的。 本手册范围内不可能提及每一个可能随时需要维修或需要其他类型的维修工作，然而根据多年的工作经验，本手册涉及的维修程序基本上能适合您的机器大部分的维修需要。 要体现自己的心血哦，不要直接拷贝翻译软件的，要流畅一些的 |
回复此楼» 猜你喜欢
求调剂
已经有3人回复
-
一志愿北京化工大学，初试成绩350求调剂
已经有14人回复
-
复试调剂
已经有4人回复
-
323分（计算机视觉和大模型项目）能直接上手
已经有3人回复
-
311分 22408 求调剂
已经有3人回复
-
320分人工智能调剂
已经有7人回复
-
一志愿郑大0705求调剂
已经有4人回复
-
0703化学
已经有10人回复
-
301求调剂
已经有10人回复
-
306分材料与化工求调剂
已经有6人回复
2楼2009-11-27 20:26:24
guyue_692
木虫 (正式写手)
水果总歼
- 应助: 0 (幼儿园)
- 金币: 6255.1
- 散金: 216
- 红花: 3
- 帖子: 519
- 在线: 231.9小时
- 虫号: 291595
- 注册: 2006-10-29
- 性别: MM
- 专业: 能源化工
3楼2009-11-27 20:27:51
4楼2009-11-27 20:33:41
★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★
guyue_692(金币+30,VIP+0):3q,good 11-27 21:06
guyue_692(金币+30,VIP+0):3q,good 11-27 21:06
|
更换轴承密封：在端盖上每一个密封点都安装有两个骨架油封，密封装置通常是这样安装的，一个密封面对着物料以隔绝物料与轴承的接触，还有一个密封面对着轴套，以保持润滑油的良好状况，当机器保养时，应对唇形密封进行检查，至少一年一次。拆除密封时，卸掉用螺钉固定在转筒端盖内表面上的固定板，然后拉出两个密封装置和密封隔离环，装进新的密封垫圈和密封件时，确认零件完全对准和无障碍。并与我们提供的机器装配图检验，以确保密封装置的正确安装，一定要确保密封装置在装配过程中不被损坏。 To replace bearing seal: two skeleton oil seals are installed in every sealing point in the end lid which is the commonly-used way for a sealing equipment: One seal face is placed towards the material as to isolate the contact between the material and the bearing while another seal face is placed towards to the bearing block to insure the good condition of the lubricants. When maintaining the machine, the lip-shaped seals should be checked at least once a year. When dismantling the seal, remove the fixed plate that is fixed by screws on the inner surface of the rolling cylinder, and then draw out the two sealing equipments and the seal rings, and install the new seal gasket and seal parts and assure the perfect dovetailing of parts and no obstacle present. And check with the provided instruction diagram to guarantee the correct installation of seal parts and make sure the seal parts not be damaged in the assembling process. |
5楼2009-11-27 20:58:00
|
强！  |
6楼2009-11-27 21:04:01
★ ★ ★ ★ ★
guyue_692(金币+5,VIP+0):3q 11-28 11:25
guyue_692(金币+5,VIP+0):3q 11-28 11:25
|
紧急处理：建议转鼓部件在新用的机件至多运转2000小时或一年应进行彻底的检查。前面提到过的临界范围的目测检查和螺栓连结的仔细检查都是必要的。 Emergency management: It is suggested that rotary drum parts in new machine undergo overhaul annually or at most operating up to 2000 hours. Aforementioned visual examination of the critical range and careful inspection of the bolts connection are required. |
7楼2009-11-27 21:06:02
★ ★ ★ ★ ★
guyue_692(金币+5,VIP+0):3q 11-28 11:26
guyue_692(金币+5,VIP+0):3q 11-28 11:26
|
本手册范围内不可能提及每一个可能随时需要维修或需要其他类型的维修工作，然而根据多年的工作经验，本手册涉及的维修程序基本上能适合您的机器大部分的维修需要。 Not every maintenance detail for the necessary repair or other type maintaining work is enclosed in this manual but based on years of working experience, what mentioned already can basically meet your most requirements for maintenance work. |
8楼2009-11-27 21:14:23
syh9288
捐助贵宾 (著名写手)
海军上将
- 翻译EPI: 6
- 应助: 2 (幼儿园)
- 金币: 1606.6
- 散金: 543
- 红花: 1
- 帖子: 1072
- 在线: 480.2小时
- 虫号: 735351
- 注册: 2009-03-30
- 性别: GG
- 专业: 有机合成
O(∩_∩)O~
★ ★ ★ ★ ★ ★ ★ ★ ★ ★
guyue_692(金币+10,VIP+0):3q 11-28 11:26
guyue_692(金币+10,VIP+0):3q 11-28 11:26
|
Replacing seal of bearing:the sealing device is usually installed in this way that in every sealing points,there are two framework oil seals. one sealing surface is in face of materials in order to isolate materials from bearings,and so as to keep a good condition of lubricant,the other is faced with spindle collar.when going on the maintenance of machine,you sould check the lip packings,at least once a year.when removing seals,at first,you can uninstall fixed plate which is attathed to the inner surface of the rotating cylinder by screwing,pull out two sealing devices and sealing spacer ring, then install new sealing washer and seals ,with ensuring the alignment and no-dysfunction of the parts. |
9楼2009-11-28 10:58:40
syh9288
捐助贵宾 (著名写手)
海军上将
- 翻译EPI: 6
- 应助: 2 (幼儿园)
- 金币: 1606.6
- 散金: 543
- 红花: 1
- 帖子: 1072
- 在线: 480.2小时
- 虫号: 735351
- 注册: 2009-03-30
- 性别: GG
- 专业: 有机合成
10楼2009-11-28 11:09:38
