24小时热门版块排行榜

返回列表

当前主题已经存档。

当前只显示满足指定条件的回帖，点击这里查看本话题的所有回帖

guyue_692

木虫 (正式写手)

水果总歼

应助: 0 (幼儿园)
金币: 6309.1
散金: 216
红花: 3
帖子: 518
在线: 231.9小时
虫号: 291595
注册: 2006-10-29
性别: MM
专业: 能源化工

[交流] 66金币求助最后几段翻译

更换轴承密封：在端盖上每一个密封点都安装有两个骨架油封，密封装置通常是这样安装的，一个密封面对着物料以隔绝物料与轴承的接触，还有一个密封面对着轴套，以保持润滑油的良好状况，当机器保养时，应对唇形密封进行检查，至少一年一次。拆除密封时，卸掉用螺钉固定在转筒端盖内表面上的固定板，然后拉出两个密封装置和密封隔离环，装进新的密封垫圈和密封件时，确认零件完全对准和无障碍。并与我们提供的机器装配图检验，以确保密封装置的正确安装，一定要确保密封装置在装配过程中不被损坏。
紧急处理：建议转鼓部件在新用的机件至多运转2000小时或一年应进行彻底的检查。前面提到过的临界范围的目测检查和螺栓连结的仔细检查都是必要的。
本手册范围内不可能提及每一个可能随时需要维修或需要其他类型的维修工作，然而根据多年的工作经验，本手册涉及的维修程序基本上能适合您的机器大部分的维修需要。

要体现自己的心血哦，不要直接拷贝翻译软件的，要流畅一些的

回复此楼

» 猜你喜欢

职称评审没过，求安慰已经有41人回复
回收溶剂求助已经有7人回复
硝基苯如何除去已经有3人回复
A期刊撤稿已经有4人回复
垃圾破二本职称评审标准已经有17人回复
投稿Elsevier的Neoplasia杂志，到最后选publishing options时页面空白，不能完成投稿已经有22人回复
EST投稿状态问题已经有7人回复
毕业后当辅导员了，天天各种学生超烦已经有4人回复
求助文献已经有3人回复
三无产品还有机会吗已经有6人回复

天使猪猪飞！

1楼 2009-11-27 19:46:47

已阅回复此楼关注TA 给TA发消息送TA红花 TA的回帖

zcy86520

铁杆木虫 (著名写手)

翻译EPI: 2
应助: 1 (幼儿园)
金币: 6354.8
散金: 832
红花: 4
帖子: 1522
在线: 243.6小时
虫号: 575365
注册: 2008-06-18
性别: GG
专业: 有机合成

★ ★ ★ ★ ★ ★ ★
guyue_692(金币+7,VIP+0):3q 11-28 11:26

Replacement Bearing Seal: In the end cover every point of a seal are installed in two skeleton oil seal, sealing device is usually installed so that a sealing face of the material in isolation from contact with the bearing material, as well as a seal faces sleeve to keep the lubricating oil in good condition, when the machine maintenance, the sealing lip should check at least once a year. Removal of seals, the relieved with the screw fixed to the rotor fixed on the inner surface of cover plate, and then pulled out two separate seals and sealing rings, put into the new sealing gaskets and seals, make sure parts complete alignment and Accessibility. We provide the machine with the assembly tested to ensure that the sealing device is installed correctly, we must ensure that the sealing device in the assembly process will not be damaged. Emergency management: It is recommended drum parts in the new parts used in operation up to 2000 hours or a year should be a thorough examination. Mentioned earlier, the critical range of visual inspection and double-check the link bolts are necessary. Within the scope of this manual may be impossible to mention every one at any time in need of repair or need other types of maintenance work, but based on years of work experience, this manual deals with the maintenance procedures for your machine can basically most of the maintenance requirements.