| 查看: 4285 | 回复: 2 | ||
[求助]
急！求助ANSYS/LS-DYNA高手，计算总是出错out-of-range velocities
|
|
slave surface of interface = 1 type = 14 surface timestep = 6.422E-04 controlling slave node ID = 2 part ID of slave node = 1 current minimum time step = 6.422E-04 master surface of interface = 1 type = 14 surface timestep = 8.102E-04 controlling master node ID = 18731 part ID of master node = 2 current minimum time step = 6.422E-04 The LS-DYNA time step size should not exceed 6.422E-04 to avoid contact instabilities. If the step size is bigger then scale the penalty of the offending surface. S t o r a g e a l l o c a t i o n Memory required to begin solution : 60166097 Additional dynamically allocated memory: 5594953 Total: 65761050 node # 1 has out-of-range velocities x-velocity= NaN y-velocity= NaN z-velocity= NaN node # 2 has out-of-range velocities x-velocity= NaN y-velocity= NaN z-velocity= NaN .............................. node # 30 has out-of-range velocities x-velocity= NaN y-velocity= NaN z-velocity= NaN E r r o r t e r m i n a t i o n 最近在做深孔钻削，先尝试只用一个细长圆柱打孔，计算时总是出现如上错误，试了很多办法均不能解决，希望大家能帮帮我，先谢谢你们了！ |
回复此楼» 猜你喜欢
售SCI一区T0P文章，我:8.O55.1.O.54,科目全,可十急
已经有6人回复
-
售SCI一区T0P文章，我:8.O.55.1.O.54,科目齐全,可+急
已经有6人回复
-
售SCI一区文章，我:8O5.5.1.O5.4,科目全,可伽急
已经有9人回复
-
售一区SCI文章T0P，我:8O.551.O54,科目全,可十急
已经有7人回复
-
售SCI文章，我:8O5.5.1.O.54,科目齐全,可+急
已经有8人回复
-
售SCI一区T0P文章，我:8.O.55.1.O54,科目全,可伽急
已经有7人回复
-
售一区SCI文章T0P，我:8O.551.O54,科目全,可十急
已经有4人回复
-
售SCI-T0P文章，我:8O.5.5.1.O.54,科目齐全,可+急
已经有6人回复
-
售SCI一区T0P文章，我:8.O55.1.O.54,科目全,可十急
已经有12人回复
-
售SCI一区文章，我:8.O.551.O.5.4,科目全,可伽急
已经有9人回复
» 本主题相关价值贴推荐，对您同样有帮助:
- 关于ansys ls-dyna结果显示的一个奇怪现象求助
已经有10人回复
- ansys/ls-dyna中怎样施加 脉冲载荷啊？急急急。。。。
已经有12人回复
2楼2014-02-28 15:19:15
3楼2014-05-22 16:36:41
10