| 查看: 463 | 回复: 1 | |||
| 本帖产生 1 个 翻译EPI ，点击这里进行查看 | |||
zoe122208木虫 (正式写手)
superboy
|
[求助]
帮忙翻译一小段汉语，谢谢
|
||
| B柱转角处破裂的原因是其受转角处拉深筋的影响。凸模和凹模的大端处拉深筋过高时，使得该处的进料阻力过大，导致破裂。对应变路径分析也表明，当降低拉深筋后，路径由复杂变简单，减少了破裂的发生。另外，通过对起皱区域起皱高度的测量以及与数值模拟的对比可知，对于热冲压而言，采用传统的起皱判定准则是可行的，即不同温度下在纯剪切状态面以下的应变点对应的板料部位判定为起皱。 |
回复此楼» 猜你喜欢
云南大学材料与能源学院解琳课题组钙钛矿博士招生
已经有7人回复
-
西安交大新媒学院副院长用撤稿论文结题
已经有5人回复
-
论文撤稿了
已经有5人回复
-
某211大学教师把个人教师官方主页改成:我跑了我跑了我跑了!官宣跑路！
已经有5人回复
-
26/27申博自荐
已经有9人回复
-
售SCI一区T0P文章，我:8.O.5.5.1.O.5.4,科目齐全,可+急
已经有3人回复
-
售SCI一区T0P文章，我:8.O.5.5.1.O.5.4,科目齐全,可+急
已经有7人回复
-
河北省自然科学基金
已经有7人回复
-
揭秘青基评审内幕：几个A才能顺利中标
已经有4人回复
-
青B发送上会通知了吗
已经有7人回复
befair
铁杆木虫 (正式写手)
- 翻译EPI: 112
- 应助: 131 (高中生)
- 金币: 12383.3
- 红花: 20
- 帖子: 661
- 在线: 608.8小时
- 虫号: 2651461
- 注册: 2013-09-13
- 性别: GG
- 专业: 宏观经济管理与战略
【答案】应助回帖
★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ...
zoe122208: 金币+70, 翻译EPI+1, ★★★★★最佳答案 2013-11-12 15:31:38
zoe122208: 金币+70, 翻译EPI+1, ★★★★★最佳答案 2013-11-12 15:31:38
|
The reason why the corner of B column fractured is that the area was impacted by the drawbead at the corner. When drawbead at the larger ends of punch-pin and die is too high, the local material feeding resistance will also be too high so that fracture is resulted. The corresponding strain path analysis shows also that when the drawbead is lowered, the path becomes simpler and fracture potential is reduced. In addition, by measuring the height of wrinkling where it occurs, and comparing with numerical simulations, it is seen that as far as hot pressing is concerned, it is feasible to follow the traditional criterion for wrinkling,i.e., the slab area corresponding to the strain spots below the pure shear plane for different temperatures, is considered to wrinkle. 匆匆，供参考 |
2楼2013-11-12 08:05:02
5