| 查看: 1683 | 回复: 2 | |||
shamrocksu铁杆木虫 (著名写手)
|
[求助]
审稿意见回来了，有一条是关于CPE元件Y数值的单位问题，请教各位 已有1人参与
|
|
审稿意见回来了，有一条是关于CPE元件Y数值的单位问题，我用的是Z-simp-win拟合的数据，软件里面没有给出单位呀，请教各位： Editor's Comments: The CPE impedance is given by Zcpe = (A^-1)((jw)^-n). The units of Z are not the same as C - they are ohm^-1 cm^-2 s^n. Admittance Ycpe = 1/Z = A(jw)^n as you have stated. The units of Y would be the inverse those of Z, or ohm^1 cm^2 s^-n. it is possible to determine C from Z, and several approaches have been developed: G. J. Brug, A. L. G. van den Eeden, M. Sluyters-Rehbach, and J. H. Sluyters, J. Electroanal. Chem., 176 (1984) 275-295 C. H. Hsu, F. Mansfeld, Corrosion 57 (2001) 747-748 B. Hirschorn, M. E. Orazem, B. Tribollet, V. Vivier, I. Frateur, and M. Musiani, Electrochimica Acta, 55 (2010), 6218-6227. In table IV you report the units of the CPE admittance as uF/cm^2. First of all, you need to use one of the above approaches to get Ccpe from Zcpe. Furthermore, those are units of capacitance determined from Z, and Y is the inverse of Z. So it is all confusing. It is better to not consider the CPE in terms of admittance. Stick to CPE impedance, Zcpe, and then determine C from Zcpe and n. Or just leave the CPE magnitude as A and use the proper units. Also - I don't like the way you designate Y and n. Qc-Y0 and Qc-n look like differences with the dash being a minus sign. Just use Y0 and n. (or better A and n) |
回复此楼» 猜你喜欢
澳大利亚皇家墨尔本理工大学（RMIT）理学院招收2027博士生
已经有62人回复
-
为什么现在电催化越来越卷？从“只看效果”到“全周期低成本”选型转变
已经有0人回复
-
物理化学论文润色/翻译怎么收费?
已经有74人回复
-
电催化氧化反应器现场运维，不可忽视的安全风险与防控措施
已经有0人回复
-
电池测试中dQ/dV怎么理解
已经有1人回复
-
精细化工浓水做零排放，前端到底该配什么氧化工艺？
已经有0人回复
-
大湾区大学姚瑶课题组2027届博士生招生 （与中山大学联合培养）
已经有25人回复
-
氯离子浓度对电催化处理效果的双重影响实测与参数优化
已经有0人回复
-
阴极协同电催化技术处理高盐难降解化工废水的机理与工程应用研究
已经有0人回复
-
氧化铝浆液
已经有2人回复
shamrocksu
铁杆木虫 (著名写手)
- 应助: 6 (幼儿园)
- 金币: 6549.7
- 散金: 19
- 红花: 2
- 帖子: 1544
- 在线: 518小时
- 虫号: 795394
- 注册: 2009-06-16
- 专业: 用于检测、分析、成像及治
2楼2013-09-12 13:11:13
3楼2020-03-06 11:13:52
