| 查看: 557 | 回复: 2 | |||
| 本帖产生 1 个 翻译EPI ，点击这里进行查看 | |||
[求助]
高手帮我润色一下，汉译英，谢谢
|
|||
|
由于缺陷与阻尼有很大的关系，即界面的缺陷较多时，能量耗散增加，使得阻尼值较大。因此，进一步分析从图2中的涂层与基体界面区的缺陷与厚度的关系，用界面缺陷（D）与界面厚度（T）的比值来表示界面区的单位厚度上的缺陷率，得出不同样品的界面区界面厚度上的缺陷率分别为： It has a great effect of defect on damping. The defect at the interface is larger, the energy dissipation is increased, so that the damping is larger. Therefore, further analyze the relationship between the defect and thickness at the interfacial region between substrate and coating. The ratio of the interface defect (D) to interface thickness (T) stand for the defect rate of unit thickness at the interfacial region, it can concluded that obtained the defect rate of unit thickness at the interfacial region for the different samples as: |
回复此楼» 猜你喜欢
323求调剂
已经有6人回复
-
一志愿北京化工大学 070300 学硕 336分 求调剂
已经有4人回复
-
352求调剂
已经有3人回复
-
一志愿东华大学化学070300，求调剂
已经有8人回复
-
277材料科学与工程080500求调剂
已经有7人回复
-
317求调剂
已经有18人回复
-
293求调剂
已经有5人回复
-
280分求调剂 一志愿085802
已经有7人回复
-
0854电子信息求调剂
已经有3人回复
-
263求调剂
已经有4人回复
phu_grassman
荣誉版主 (知名作家)
快乐岛、布吉岛岛主
- 翻译EPI: 265
- 应助: 7 (幼儿园)
- 贵宾: 1.392
- 金币: 7538.7
- 散金: 11599
- 红花: 107
- 沙发: 11
- 帖子: 5611
- 在线: 1480.2小时
- 虫号: 1151372
- 注册: 2010-11-20
- 专业: 电化学
- 管辖: English Cafe
【答案】应助回帖
|
由于缺陷与阻尼有很大的关系，即界面的缺陷较多时，能量耗散增加，使得阻尼值较大。因此，进一步分析从图2中的涂层与基体界面区的缺陷与厚度的关系，用界面缺陷（D）与界面厚度（T）的比值来表示界面区的单位厚度上的缺陷率，得出不同样品的界面区界面厚度上的缺陷率分别为： Due to the close relationship between defects and damping that an increase in the amount of defects at the interface can increase energy dissipation, thus resulting in greater damping, the relationship between the defect and thickness at the interfacial region between the substrate and the coating was further analyzed. The ratio of the interface defect (D) to interface thickness (T) stands for the defect rate per unit thickness at the interfacial region. And the defect rate per unit thickness at the interfacial region for the different samples were derived respectively. |
2楼2013-04-13 09:56:30
【答案】应助回帖
★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★ ★
wxqtjw: 金币+20, 翻译EPI+1, ★★★★★最佳答案 2013-04-13 10:16:14
wxqtjw: 金币+20, 翻译EPI+1, ★★★★★最佳答案 2013-04-13 10:16:14
| Damping is greatly affected by defects, i.e. the larger the defects at the interface, the larger the damping value is as the energy dissipation is increased. Therefore, through further analysis of the relationship between the defects and thickness at the interfacial region between substrate and coating from Figure 2, using the ratio of the interface defect (D) to interface thickness (T) to indicate the defect rate of unit thickness at the interfacial region, it is obtained that the defect rates of unit thickness at the interfacial region for the different samples are as follows: |
3楼2013-04-13 10:09:03
