| 查看: 3668 | 回复: 29 | |||
| 当前只显示满足指定条件的回帖，点击这里查看本话题的所有回帖 | |||
hudasuhai木虫 (著名写手)
|
[交流]
Journal of Manufacturing Science and Engineering 意见回来了！！ 已有17人参与
|
||
|
Journal of Manufacturing Science and Engineering 意见回来了！！三个专家，两个同意，意见还是不错，另外一个专家的意见极差。 怎么办啊？而且差意见的专家就是否定了工作，都不知道怎么回复好，编辑给了大修，虫虫们有这样的经历不啊？ 指望这文章呢！！！！！！！哎 Review has been completed on your paper. Based on the detailed comments of the reviewers, I am recommending to the Journal Editor that your paper be considered for publication as a Research Paper in the Journal of Manufacturing Science and Engineering pending further revision. My recommendation is: Major revisions required. Reviewer 1: -this paper has many grammatical and writing errors which are very distracting -the size of the vessel for the simulations conducted is very small wrt industrial sized vessels, with only minor mentioning of scaling -No experimental validation or testing to show that this work is valid -Significance of the work is shallow. Not worthy of this journal. Reviewer 2: This manuscript presents the numerical analysis of stir casting of aluminum matrix composites using a commercial software package, ANSYS/Fluent. The flow patterns associated with various stirrer configurations, stirring speeds, and stirrer angles were analyzed and the regions and volumes of stagnant and dead zones were examined to determine the optimal process conditions and stirrer and crucible designs. Overall, the study is fairly complete and the predictions seem to be reasonable. However, there are a number of areas that need to be revised, as listed below, for purposes of clarification or completeness prior to publication. 1. While the results were shown on the axis cross sections, the flow field should be three-dimensional because the geometry of the stirrer blades is not axis symmetrical. Please clarify if the analysis was done in three-dimensions or not. In addition, it looks like only the velocity components are on the plane of the axis cross sections. The authors should also include some prediction results on the planes (r-theta plane) that are perpendicular to the axis of the crucible. 2. The authors stated that “From initial trials and Reynolds number examination, the k-(zeta) turbulent model and the laminar flow model were chosen to model the mixer system.” However, in the results subsequently presented, it is not clear at all which model (turbulent or laminar) they corresponded to. The authors should include the corresponding Reynolds number and model type in the tables. This will help to substantiate the remarks made by the authors corresponding to Figs. 7 (d) and (e) that state: “.. the turbulence was apparently viewed in the crucible…” 3. Please include the criteria of stagnant and dead zones (in terms of velocity or other criterion). 4. The stirrer angle information is missing for Figure 3 and Table 1. 5. The following sentence (above Table 1) needs to be rewritten: “While the multi-stage stirrer yielded the relatively satisfactory flow pattern to disperse the ceramic particles in the molten matrix compared with the other two stirrer geometries.” 6. It is not clear what criterion was used to determine that the axial velocity is large enough to suck the air from the fluid surface and cause gas entrapment. 7. Please elaborate on why the “frictionless” (instead of “no-slip”) boundary condition was imposed on the surface of the crucible. 8. Page 3: “…, polymerization, etc [15, 16].” should be ““…, polymerization, etc. [15, 16].” 9. Page 8: “… without a axial suction …” should be “… without an axial suction …” Reviewer 3: This paper reports theoretical work on the flow behavior of fluid in a stir casting. A finite element method was used to simulate the flow pattern of fluid in a vassal during stir casting. The authors discussed the several parameters that affect the flowing patterns and particle distributions. This is an interesting paper and it is recommended for publication. 文章经历： 这篇文章去年底投了MMP，就一个专家意见，还不错，编辑给大修，返回后，再审，结果被枪毙了，后来按照给的意见，修改投了这期刊，现在还是大修。 苦！苦行僧 真的是大修，修怕了！ 这些专家一个意见在天上，一个意见在地下，一个意见这么悬在中间！怎么回复好啊？？？？？？？？？？？？？？？？ [ Last edited by hudasuhai on 2010-6-18 at 08:28 ] |
回复此楼» 猜你喜欢
一志愿中科大材料与化工，353分还有调剂学校吗
已经有13人回复
-
085600材料与化工调剂
已经有6人回复
-
320求调剂
已经有6人回复
-
期刊推荐
已经有5人回复
-
有没有接收比较快的sci期刊呀，最好在一个月之内的，研三孩子求毕业
已经有7人回复
-
又一批高校组建人工智能学院 师资行吗 不是骗人吗
已经有4人回复
-
297，工科调剂?河南农业大学本科
已经有15人回复
-
337求调剂
已经有3人回复
-
申博/考博
已经有5人回复
-
申博
已经有3人回复
hudasuhai
木虫 (著名写手)
- 应助: 13 (小学生)
- 金币: 2964.5
- 散金: 131
- 红花: 4
- 帖子: 1310
- 在线: 386.2小时
- 虫号: 748711
- 注册: 2009-04-14
- 性别: GG
- 专业: 元素化学
28楼2010-07-05 15:32:02
zhangchandyf
木虫 (正式写手)
- 应助: 5 (幼儿园)
- 金币: 4755.8
- 散金: 36
- 红花: 2
- 帖子: 858
- 在线: 426.7小时
- 虫号: 425981
- 注册: 2007-07-28
- 性别: GG
- 专业: 药物设计与药物信息
2楼2010-06-17 09:13:56
3楼2010-06-17 09:21:27
hudasuhai
木虫 (著名写手)
- 应助: 13 (小学生)
- 金币: 2964.5
- 散金: 131
- 红花: 4
- 帖子: 1310
- 在线: 386.2小时
- 虫号: 748711
- 注册: 2009-04-14
- 性别: GG
- 专业: 元素化学
4楼2010-06-17 09:23:09
5