| 查看: 392 | 回复: 4 | |||
| 当前主题已经存档。 | |||
| 本帖产生 1 个 翻译EPI ，点击这里进行查看 | |||
| 当前只显示满足指定条件的回帖，点击这里查看本话题的所有回帖 | |||
shmily5368银虫 (小有名气)
|
[交流]
这是什么制备工艺?
|
||
| gas pressure infiltration |
回复此楼» 猜你喜欢
工科08-机械专硕-求调剂
已经有3人回复
-
一志愿苏州大学材料工程（085601）专硕有科研经历三项国奖两个实用型专利一项省级立项
已经有9人回复
-
材料工程302分求调剂
已经有8人回复
-
315求调剂
已经有14人回复
-
307分材料专业求调剂
已经有7人回复
-
材料调剂
已经有11人回复
-
262求调剂
已经有6人回复
-
一志愿北京交通大学材料工程总分358求调剂
已经有4人回复
-
一志愿青科085500，初试295分，公共课213分
已经有3人回复
-
304求调剂
已经有3人回复
shmily5368
银虫 (小有名气)
- 应助: 0 (幼儿园)
- 金币: 1329.5
- 散金: 20
- 帖子: 100
- 在线: 13.8小时
- 虫号: 800905
- 注册: 2009-06-29
- 专业: 结构陶瓷
3楼2010-04-19 21:20:50
shmily5368(金币+2, 翻译EPI+1): 2010-04-19 21:21
|
Gas pressure infiltration (GPI) is process for preparation of composite materials where molten matrix material is infiltrated into the pores of preform under the influence of high gas pressure. Technology usually has several steps: evacuation of pressure vessel (some material as Mg are heated under protective gas because of the evaporation which can damage equipment), heating under vacuum until matrix material is melted, immersion of porous preform into the melt, infiltration under high pressure and withdrawal of the sample from the melt (in case of some material systems were wettability is not sufficient, sample solidifies together with matrix in crucible). In some cases bonding between constituents is established due to the chemical reaction at the interface (for example formation of carbides), but sometimes this bond is only mechanical. Cross section of typical gas pressure infiltration equipment showing pressure vessel, insulation of the pressure vessel, heating element and crucible which is used for material melting Steps of gas pressure infiltration process: a) porous preform above matrix material during heating; b) immersion of porous preform into the molten matrix material and inlet of pressurized gas; c) infiltrated sample in molten matrix and d) withdrawal of infiltrated sample from the melt As mentioned before, terms which are very often related with gas pressure infiltration technology are wettability or wetting angle. Wetting is determinated by contact angle between liquid phase and solid substrate. GPI process is used because in some cases wetting angle between molten matrix and solid porous reinforcement is relatively high. To overcome this problem high pressure must be used. If wetting angle is 90° or lower, this is considered as good. Sometime, wetting angle between constituents is so high (pure copper/carbon fibres) that not even extremely high pressure cannot ensure good infiltration results |
2楼2010-04-19 19:38:13
4楼2010-04-19 21:51:57
5楼2010-04-19 21:52:08
