| 查看: 406 | 回复: 8 | |||
| 当前主题已经存档。 | |||
| 当前只显示满足指定条件的回帖，点击这里查看本话题的所有回帖 | |||
[交流]
求译一段话
|
|||
| 以等体积浸渍法制备了摩尔比为10，3，1，1/3，1/10，负载量为5%，10%，15%，20%，25%，30%的M-F/Al2O3颗粒。典型合成过程如下：首先取一定量的Al2O3在500度煅烧4小时后筛分至20-40目留用。Al2O3参数列于表一。根据已计算的Mn、Fe摩尔比及负载量，称取定量Fe(NO3)3及Mn(NO3)2溶于去离子水中,搅拌至均匀。将混合溶液以气雾形式喷入瞬时搅拌的Al2O3颗粒中，密封老化24h，而后转入110℃下恒温干燥箱干燥2h，接着以1℃/min的速率程序升温至500℃焙烧4h，最后退火冷却至室温。另外，考虑到浸渍过程酸碱中和方式的影响，实验过程还分别添加了四甲基氢氧化铵（0.0135mol）及氨水（0.0135mol）进行比较。 |
回复此楼» 猜你喜欢
面上项目申报
已经有3人回复
-
有时候真觉得大城市人没有县城人甚至个体户幸福
已经有5人回复
-
酰胺脱乙酰基
已经有9人回复
-
CSC & MSCA 博洛尼亚大学能源材料课题组博士/博士后招生｜MSCA经费充足、排名优
已经有5人回复
-
有70后还继续奋斗在职场上的吗？
已经有6人回复
-
博士延得我，科研能力直往上蹿
已经有7人回复
-
退学或坚持读
已经有27人回复
-
面上基金申报没有其他的参与者成吗
已经有5人回复
-
遇见不省心的家人很难过
已经有22人回复
slowstar
木虫 (职业作家)
- 翻译EPI: 13
- 应助: 12 (小学生)
- 金币: 16733.5
- 红花: 2
- 帖子: 3381
- 在线: 803小时
- 虫号: 712881
- 注册: 2009-03-02
- 性别: GG
- 专业: 热力学
9楼2009-10-13 20:19:29
★
harmile(金币+1,VIP+0):你这个是机器翻译的~~~~ 10-12 22:38
harmile(金币+1,VIP+0):你这个是机器翻译的~~~~ 10-12 22:38
| Prepared by impregnation with an equal volume of the molar ratio of 10,3,1,1 / 3,1 / 10, the load capacity of 5%, 10%, 15%, 20%, 25%, 30% of the MF/Al2O3 particles. A typical synthesis process is as follows: First, take a certain amount of Al2O3 calcined at 500 degrees for 4 hours, sieving to 20-40 mesh retained. Al2O3 parameters listed in Table 1. Has been calculated according to the Mn, Fe molar ratio and load, that take quantitative Fe (NO3) 3 and Mn (NO3) 2 dissolved in deionized water, stirring to evenly. The mixed solution in the form of aerosol spray into the instantaneous mixing of the Al2O3 particles, sealing aging 24h, then transferred to drying oven at 110 ℃ temperature 2h, followed by 1 ℃ / min rate of temperature programmed to 500 ℃ calcined 4h, the final annealing cooled to room temperature. In addition, taking into account the pH in the impregnation process and methods of the experimental process also were added to 4-methyl ammonium hydroxide (0.0135mol) and ammonia (0.0135mol) were compared. . |
2楼2009-10-12 20:35:15
slowstar
木虫 (职业作家)
- 翻译EPI: 13
- 应助: 12 (小学生)
- 金币: 16733.5
- 红花: 2
- 帖子: 3381
- 在线: 803小时
- 虫号: 712881
- 注册: 2009-03-02
- 性别: GG
- 专业: 热力学
incipient wetness impregnation4楼2009-10-13 08:21:20
|
或者谁对照中文帮忙修正一下~~ The particles with Mn/Fe molar ratios of 10, 3, 1, 1/3, 1/10 and different loading were prepared by incipient wetness impregnation [17]. A typical synthetic procedure was as follows: firstly took a certain amount of Al2o3 calcined at 500C for 4 hours, then retained them as support (20-40 mute). Properties of Al2o3 are listed in Table 1. According to the calculated molar ratio and loading, took quantitative Fe (NO3) 3 and Mn(NO3)2 into solution by adding deionized water. Further, sprayed the mixed solution into particles (5g) and instantaneous stirred at the same time. sealed and aged for 24 hours in the air, and then transferred them to thermostatic drying oven dried for 2h at 110C, followed by 1 C/min rate temperature-programmed to 500C and calcinated for 4h, the final cooled to ambient temperature. Besides, considered partially alkali neutralization, 0.0135mol tetramethy-lammonium hydroxide (25%, AR, Sinopharm Chemical Reagent Co., Ltd) and 0.0135mol aqueous ammonia ( AR, Sinopharm Chemical Reagent Co., Ltd) are used in the process of impregnation. Definitions of the above samples are shown in Table 2. 帮忙润化一下~~~ |
5楼2009-10-13 10:54:02