| 查看: 1907 | 回复: 11 | ||||
| 当前主题已经存档。 | ||||
| 当前只显示满足指定条件的回帖，点击这里查看本话题的所有回帖 | ||||
[交流]
ISOR 的作用
|
||||
|
谁知道ISOR 的作用的作用啊 在什么情况下用这个啊？ Most readers will have no idea what ISOR means. Please explain how you treated the parameters of your structural model. 这个怎么回答呢？ 在解析过程中用了ISOR 0.001 C1 C2 C3 C4 O13 O9 O4 |
回复此楼» 收录本帖的淘帖专辑推荐
 软件专辑以及解析晶体相关问题 |
» 猜你喜欢
江西科技师范大学物理化学课题组接收调剂生，名额还有，速来
已经有0人回复
-
求碳酸钠和碳酸氢钠的晶胞结构图或晶体结构图
已经有0人回复
-
无机化学论文润色/翻译怎么收费?
已经有216人回复
-
求碳酸钠和碳酸氢钠的晶胞结构图或晶体结构图
已经有0人回复
-
江西科技师范大学物理化学课题组接收调剂生，12点开启，速来
已经有0人回复
-
【2026 考研调剂】哈尔滨工程大学 招收学硕调剂生（英语一、数学一）
已经有0人回复
-
四川轻化工大学化学与环境工程学院 付昱教授课题组招收调剂硕士研究生
已经有11人回复
-
大连化物所招收有机背景的博士候选人
已经有0人回复
7楼2009-05-05 11:07:00
zhaoyangqufu
至尊木虫 (知名作家)
- CMEI: 3
- 应助: 16 (小学生)
- 金币: 15924.8
- 散金: 242
- 红花: 10
- 帖子: 6571
- 在线: 215.2小时
- 虫号: 440284
- 注册: 2007-10-27
- 性别: GG
- 专业: 无机化学
2楼2009-05-04 10:05:43
xi2004
至尊木虫 (职业作家)
- CMEI: 10
- 应助: 125 (高中生)
- 金币: 16769.9
- 散金: 12393
- 红花: 221
- 帖子: 4161
- 在线: 436.9小时
- 虫号: 354550
- 注册: 2007-04-24
- 专业: 结构化学
★ ★ ★ ★ ★ ★
xglegl(金币+5,VIP+0): 5-4 18:55
paopaomeng(金币+1,VIP+0):谢谢交流 5-4 19:28
xglegl(金币+5,VIP+0): 5-4 18:55
paopaomeng(金币+1,VIP+0):谢谢交流 5-4 19:28
|
残酷 好用词. 以下抄自说明书 1. Isolated (e.g. solvent water) atoms may be restrained to be approximately isotropic, e.g. to prevent them going 'non-positive-definite'; this is a rough approximation and so should be applied as a 'soft' restraint with a large esd (ISOR). 2. ISOR 0.1 O_201 > LAST ! Approximate isotropic restraints for waters; ! ignored for isotropic 3. ISOR s[0.1] st[0.2] atomnames The named atoms are restrained with effective standard deviation s so that their U ij components approximate to isotropic behavior; however the corresponding isotropic U is free to vary. ISOR is often applied, perhaps together with SIMU, to allow anisotropic refinement of large organic molecules when the data are not adequate for unrestrained refinement of all the U ; in particular ISOR can be applied to solvent water for which DELU and SIMU are ij inappropriate. ISOR should in general be applied as a weak restraint, i.e. with relatively large sigmas, for the reasons discussed above (see SIMU); however it is also useful for preventing individual atoms from becoming 'non-positive-definite'. However it should not be used indiscriminately for this purpose without investigating whether there are reasons (e.g. disorder, wrong scattering factor type etc.) for the atom going n.p.d. If (according to the connectivity table, i.e. ignoring attached hydrogens) the atom is terminal (or makes no bonds), st is used instead as the esd. If s but not st is specified, st is set to twice s. If no atoms are given, all non-hydrogen atoms are understood. SFAC element names may also be referenced, preceded by '$'. s or st may be set to zero to switch offthe appropriate restraints. ISOR without atom names (or ISOR_* if residues are used) applies this restraint to all non-hydrogen atoms. Note also the use of the keyword 'LAST' to indicate the last atom in the .ins file; an anisotropic refinement of a macromolecule will often include: ISOR 0.1 O_201 > LAST assuming that the solvent water starts with O_201 and continues until the end of the atom list. ISOR should in general be given a much larger esd (and hence lower weight) than DELU; whereas there is good evidence that DELU restraints should hold accurately for most covalently bonded systems, ISOR (and SIMU) are only rough approximations to reality. |
4楼2009-05-04 17:58:11
lizuoxi
金虫 (正式写手)
- 应助: 0 (幼儿园)
- 金币: 1009.3
- 散金: 807
- 红花: 1
- 帖子: 611
- 在线: 187小时
- 虫号: 465247
- 注册: 2007-11-22
- 专业: 结构化学
5楼2009-05-04 20:02:51