| 查看: 820 | 回复: 8 | |||
| 当前只显示满足指定条件的回帖，点击这里查看本话题的所有回帖 | |||
姜呃呃新虫 (小有名气)
|
[交流]
单元类型
|
||
|
求助大神:用solid90热分析求解，用solid186结构分析求解。进行单元类型转换时出现错误说“solid186没有温度自由度，所以etchg tts命令忽略了solid186”.进行结构分析要啥温度自由度？还有要是我选择的单元本来就有温度与X Y Z自由度就不用进行单元类型转换啊？例如plane13 solid5 发自小木虫Android客户端 |
回复此楼» 猜你喜欢
有没有人能给点建议
已经有5人回复
-
假如你的研究生提出不合理要求
已经有12人回复
-
实验室接单子
已经有7人回复
-
全日制（定向）博士
已经有5人回复
-
萌生出自己或许不适合搞科研的想法，现在跑or等等看？
已经有4人回复
-
Materials Today Chemistry审稿周期
已经有4人回复
-
参与限项
已经有3人回复
-
对氯苯硼酸纯化
已经有3人回复
-
所感
已经有4人回复
-
要不要辞职读博？
已经有7人回复
姜呃呃
新虫 (小有名气)
- 应助: 0 (幼儿园)
- 金币: 80.4
- 散金: 10
- 帖子: 84
- 在线: 13.7小时
- 虫号: 6319137
- 注册: 2017-04-14
- 性别: GG
- 专业: 制造系统与自动化
送红花一朵 |
对流换热系数也要删掉么？我只是删掉了ddele,all,temp没有进行sfdele。电脑只是进行了警告elements of type solid186 do not have a temperature degree of freedom so the etchg tts command ignoees them.还有一个问题就是热分析结束后没有rth文件，我百度大家说用rst 文件也可以，我的rst文件我用list result打开里面是有结果的，但是我在ldread的时候说我的.rst文件 is not available. 谢谢！！！！ 发自小木虫Android客户端 |
3楼2017-12-13 12:30:54
shgao20
专家顾问 (职业作家)
-
专家经验: +809 - 仿真EPI: 1
- 应助: 1311 (讲师)
- 金币: 13381.4
- 红花: 267
- 帖子: 3531
- 在线: 473.4小时
- 虫号: 3644138
- 注册: 2015-01-14
- 专业: 动力学与控制
- 管辖: 仿真模拟
2楼2017-12-13 07:53:08
shgao20
专家顾问 (职业作家)
-
专家经验: +809 - 仿真EPI: 1
- 应助: 1311 (讲师)
- 金币: 13381.4
- 红花: 267
- 帖子: 3531
- 在线: 473.4小时
- 虫号: 3644138
- 注册: 2015-01-14
- 专业: 动力学与控制
- 管辖: 仿真模拟
4楼2017-12-14 07:34:48
姜呃呃
新虫 (小有名气)
- 应助: 0 (幼儿园)
- 金币: 80.4
- 散金: 10
- 帖子: 84
- 在线: 13.7小时
- 虫号: 6319137
- 注册: 2017-04-14
- 性别: GG
- 专业: 制造系统与自动化
|
finish /clear /title,'thermal spraying 20171212' /prep7 /unit,si et,1,solid90 et,2,solid186 mptemp,1,0,300,600,1000,1300,2000 mpdata,dens,1,1,7859,7770,7659,7600,6750 ,6750 mpdata,dens,2,1,7859,7770,7659,7600,6750 ,6750.001 mpdata,c,1,1,450,514,967,1370,2800,2000 mpdata,c,2,1,450,514,967,1370,2800,2000.001 mpdata,kxx,1,1,67,53,39,31,20,20 mpdata,kxx,2,1,67,53,39,31,20,20.001 csys,0 block,0,0.1,0,0.02,0,0.01 block,0,0.1,0,0.02,0.01,0.012 vglue,all nummrg,all numcmp,all type,1 mat,2 esize,0.005 vmesh,2 type,1 mat,1 esize,0.005 vmesh,1 eplot finish /solu autots,on cnvtol,heat,,,,-1 outpr,all,all outres,all,all kbc,1 antype,trans timint,off nsubst,4 nsel,all d,all,temp,20 time,0.01 solve esel,s,mat,,2 ekill,all esel,all time,0.02 timint,on,therm tintp,,,,1.0 ddele,all,temp alls asel,a,,,3,5,1 nsla,s sf,all,conv,30,20 t=0 time=0.02 esel,s,live eplot *do,j,1,2 *do,i,1,20 ddele,all,temp t=t+1 esel,s,elem,,t ealive,all nsle d,all,temp,100 esel,s,live eplot alls time=time+0.1 nsubst,2,10,1 lnsrch,on time,time solve *enddo t=t+20 *do,p,1,20 ddele,all,temp esel,s,elem,,t ealive,all nsle d,all,temp,100 esel,s,live eplot alls t=t-1 time=time+0.1 nsubst,2,10,1 lnsrch,on time,time solve *enddo t=t+20 time=time+1 time,time nsubst,1 solve *enddo time=time+3600 time,time ddele,all,temp nsubst,10 allsel,all solve sfdele,all,conv save finish /prep7 etchg,tts mptemp mptemp,1,0,300,600,1000,1300,1400,2000 mpdata,ex,1,1,2e11,1.86e11,1.35e11,2e10,2e7,2e7,2e7 mpdata,ex,2,1,2e11,1.86e11,1.35e11,2e10,2e7,2e7,2.000001e7 mpdata,prxy,1,1,0.33,0.33,0.35,0.36,0.4,0.4 mpdata,prxy,2,1,0.33,0.33,0.35,0.36,0.4,0.400001 mpdata,alpx,1,1,12e-6,12.6e-6,13.0e-6,13.4e-6,13.7e-6,14e-6 mpdata,alpx,2,1,12e-6,12.6e-6,13.0e-6,13.4e-6,13.7e-6,14.0001e-6 mp,reft,1,20 mp,reft,2,100 tb,bkin,1,5 tbtemp,15 tbdata,1,280e6,2e9 tbtemp,800 tbdata,1,10e6,1e7 tbtemp,2500 tbdata,1,10e6,1e6 tbcopy,bkin,1,2 /solu asel,s,area,,1 nsla,s d,all,uz,0 antype,trans outpr,all,all outres,all,all kbc,0 autots,on time,0.02 esel,s,mat,,2 ekill,all allsel,all nsubst,1 solve t=0 time=0.02 *do,j,1,10 *do,i,1,20 ddele,all,temp t=t+1 esel,s,elem,,t ealive,all alls time=time+0.1 time,time ldread,temp,,,time,,,rst nsubst,2,10,1 lnsrch,on *enddo t=t+20 *do,p,1,20 ddele,all,temp esel,s,elem,,t ealive,all alls time=time+0.1 time,time ldread,temp,,,time,,,rst t=t-1 nsubst,2,10,1 lnsrch,on solve *enddo ddele,all,temp t=t+20 time=time+1 time,time ldread,temp,,,time,,,rst nsubst,1 solve *enddo time=time+3600 time,time ldread,temp,,,time,,,rst nsubst,10 allsel,all solve finish /post1 set,,,,,2.02 plnsol,temp plnsol,s,eqv |
5楼2017-12-14 12:24:00