| 查看: 810 | 回复: 2 | |||
[交流]
ansys计算不收敛 已有1人参与
|
小弟在做ansys接触分析时计算不收敛 求大神指点 跪谢！！ ~8R2J8ED1B0{HK[6E]$E369.png |
回复此楼» 猜你喜欢
售一区SCI文章T0P，我:8O.551.O54,科目全,可十急
已经有3人回复
-
售SCI一区文章，我:8.O.551.O.5.4,科目全,可伽急
已经有3人回复
-
售SCI一区T0P文章，我:8.O55.1.O.54,科目全,可十急
已经有3人回复
-
售SCI一区T0P文章，我:8O.55.1.O.54,科目全,可伽急
已经有4人回复
-
售SCI一区T0P文章，我:8O.55.1.O.5.4,科目齐全,可+急
已经有3人回复
-
售SCI一区文章，我:8O5.5.1.O5.4,科目全,可伽急
已经有3人回复
-
售SCI一区T0P文章，我:8.O.55.1.O.5.4,科目全,可+急
已经有3人回复
-
售SCI-T0P文章，我:8O.5.5.1.O.54,科目齐全,可+急
已经有3人回复
-
售SCI一区T0P文章，我:8.O.55.1.O.5.4,科目全,可+急
已经有3人回复
-
售一区SCI文章T0P，我:8O.551.O54,科目全,可十急
已经有3人回复
mygt_hit
专家顾问 (职业作家)
-
专家经验: +362 - EPI: 1
- 应助: 438 (硕士)
- 贵宾: 0.019
- 金币: 19579.9
- 散金: 5130
- 红花: 135
- 沙发: 3
- 帖子: 4939
- 在线: 990.5小时
- 虫号: 1489764
- 注册: 2011-11-13
- 性别: GG
- 专业: 结构工程
- 管辖: 土木建筑
2楼2016-02-24 18:17:39
|
大神您好 我是在做岩土体开挖设置接触元的时候出现了这样的问题， 我在网上看到是说接触对设置太多可能会出现这样的情况，具体不清楚，地应力的计算都还可以 开挖之后就结果不好了 支护之后都不收敛了。下面是我具体出现的问题警告。请问需要怎么解决呢 *** WARNING *** CP = 206.375 TIME= 10:54:29 There are 74 small equation solver pivot terms. *** ERROR *** SUPPRESSED MESSAGE CP = 206.391 TIME= 10:54:29 The value of UX at node 126 is 2.681589959E+11. It is greater than the current limit of 1000000. This generally indicates rigid body motion as a result of an unconstrained model. Verify that your model is properly constrained. *** ERROR *** SUPPRESSED MESSAGE CP = 206.391 TIME= 10:54:29 *** MESSAGE CONTINUATION ---- DIAGNOSTIC INFORMATION *** If one or more parts of the model are held together only by contact verify that the contact surfaces are closed. You can check contact status in the SOLUTION module for the converged solutions using CNCHECK. *** ERROR *** SUPPRESSED MESSAGE CP = 206.406 TIME= 10:54:29 *** MESSAGE CONTINUATION ---- DIAGNOSTIC INFORMATION *** Rigid body motion can also occur when net section yielding has occurred resulting in large displacements for small increments of load or when buckling has occurred. You can plot the time history curve for node 126 in the UX direction to check for stiffness (slope of the curve) approaching zero. *** WARNING *** SUPPRESSED MESSAGE CP = 206.406 TIME= 10:54:29 The unconverged solution (identified as time 3.35 substep 999999) is output for analysis debug purposes. Results should not be used for any other purpose. |
3楼2016-02-25 11:27:18
