| 查看: 240 | 回复: 0 | ||
[求助]
分网求助，程序中最后那个体10，分网不成，紧急求助，高手明示
|
|
finish /clear /FILNAME,abcd /prep7 /uis,msgpop,3 /nerr,0,90000000 *afun,deg !角度单位设为度，不是弧度 !单元类型 et,2,solid186 !3D 20节点六面体单元 et,1,mesh200 !网格划分单元 keyopt,1,1,7 !定义材料属性(线性） mp,ex,1,2e5 !弹性模量Mpa mp,prxy,1,0.3 !泊松比 mp,dens,1,7.85e-9 !密度t/mm3 k,1,0,-115,0 !1-点号，xyz坐标值 k,2,16,-99,0 k,3,16,-67.6,0 lstr,2,3 clocal,11,1,0,-99,0 !在原点处定义一个柱坐标系（R,θ,z)，为能画出圆孔在该坐标系下建立以下点 l,1,2 csys,0 K,4,0,-129,0 kwpave,4 !移动工作平面的原点到拾取关键点的中间位置 wprota,,,-90 wprota,-45,, cyl4,,,14 lstr,5,7 !get line L7 lstr,6,8 wprota,,-90, asbw,1 wprota,,,-90 asbw,all ldele,7 ldele,8 nummrg,all !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! na1=20 !trajpar pertition na2=8 !圆弧划分段数 LESIZE,1,,,na1 LESIZE,2,,,na1 LESIZE,3,,,na2 LESIZE,4,,,na2 LESIZE,5,,,na2 LESIZE,6,,,na2 LESIZE,10,,,na2 LESIZE,11,,,na2 LESIZE,12,,,na2 LESIZE,13,,,na2 type,1 MSHAPE,0 !0---2d用四边形，3d用六面体 MSHKEY,1 !0---free,1---mapped,2-----mapped if possible nummrg,area AMESH,ALL type,2 vdrag,1,4,5,6,,,2,1 !adele,all !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! alls !........................其实用csys,1,0可以立即将工作坐标系移到global k,50,16,0,0 csys,4 kwpave,50 !移动工作平面的原点到拾取关键点的中间位置 wprota,,90, wprota,45 cyl4,,,16.5 cyl4,,,40 asba,30,29 rectng,-45,-30,50,-50 asba,31,29 alls !nummrg,all lstr,21,31 lstr,21,32 l,20,24 l,19,23 l,22,26 na3=8 LESIZE,49,,,na3 LESIZE,41,,,na3 LESIZE,44,,,na3 LESIZE,50,,,na3 LESIZE,51,,,na3 LESIZE,42,,,na3 LESIZE,43,,,na3 LESIZE,37,,,na3 LESIZE,38,,,na3 LESIZE,39,,,na3 LESIZE,40,,,na3 LESIZE,45,,,na3 LESIZE,46,,,na3 LESIZE,47,,,na3 type,1 MSHAPE,0 !0---2d用四边形，3d用六面体 MSHKEY,2 !0---free,1---mapped,2-----mapped if possible AMESH,30 asel,s,,,30 type,2 !选择1号体单元solid186 extopt,esize,8 !厚度方向拉伸段数 vext,all,,,,,-14 !拉伸距离 alls lstr,14,29 lstr,15,32 lstr,18,28 lstr,17,31 al,70,24,69,63 !建过渡面 al,53,69,36,71 al,71,33,72,62 al,30,72,51,70 !al,30,33,36,24 va,33,40,41,42,43,20,23,26,28 na4=8!过渡段边线分段 LESIZE,69,,,na4,+2 LESIZE,70,,,na4,+2 LESIZE,71,,,na4,+2 LESIZE,72,,,na4,+2 type,2 MSHAPE,0 !0---2d用四边形，3d用六面体 MSHKEY,0 !0---free,1---mapped,2-----mapped if possible vmesh,10 |
回复此楼» 猜你喜欢
售SCI一区文章，我:8 O5 51O 54,科目齐全
已经有3人回复
-
售SCI一区文章，我:8 O5 51O 54,科目齐全
已经有3人回复
-
售SCI一区文章，我:8 O5 51O 54,科目齐全
已经有4人回复
-
售SCI一区文章，我:8 O5 51O 54,科目齐全
已经有3人回复
-
售SCI一区文章，我:8 O5 51O 54,科目齐全
已经有5人回复
-
售SCI一区文章，我:8 O5 51O 54,科目齐全
已经有5人回复
-
售SCI一区文章，我:8 O5 51O 54,科目齐全
已经有5人回复
-
售SCI一区文章，我:8 O5 51O 54,科目齐全
已经有6人回复
-
售SCI一区文章，我:8 O5 51O 54,科目齐全
已经有6人回复
-
售SCI一区文章，我:8 O5 51O 54,科目齐全
已经有6人回复
» 本主题相关商家推荐: (我也要在这里推广)
10