| 查看: 218 | 回复: 0 | |||
| 当前主题已经存档。 | |||
zzq122zzq木虫 (正式写手)
|
[交流]
MIT研制出燃料电池新材料,功率输出提高到50%以上
|
||
|
麻省理工学院(MIT)的工程师改进了一种燃料电池，功率输出比提高到50%以上，该技术使得这些环境友好的储能器件具有极为广阔的市场前景，尤其是在微电子器件方面。 -------------------------------------------------------------------------------- MIT Creates New Material For Fuel Cells, Increases Power Output By 50 Percent The new material key to the work is also considerably less expensive than its conventional industrial counterpart, among other advantages. “Our goal is to replace traditional fuel-cell membranes with these cost-effective, highly tunable and better-performing materials,” said Paula T. Hammond, Bayer Professor of Chemical Engineering and leader of the research team. She noted that the new material also has potential for use in other electrochemical systems such as batteries. The work was reported in a recent issue of Advanced Materials by Hammond, Avni A. Argun and J. Nathan Ashcraft. Argun is a postdoctoral associate in chemical engineering; Ashcraft is a graduate student in the same department. Like a battery, a fuel cell has three principal parts: two electrodes (a cathode and anode) separated by an electrolyte. Chemical reactions at the electrodes produce an electronic current that can be made to flow through an appliance connected to the battery or fuel cell. The principal difference between the two" Fuel cells get their energy from an external source of hydrogen fuel, while conventional batteries draw from a finite source in a contained system. The MIT team focused on direct methanol fuel cells (DMFCs), in which the methanol is directly used as the fuel and reforming of alcohol down to hydrogen is not required. Such a fuel cell is attractive because the only waste products are water and carbon dioxide (the latter produced in small quantities). Also, because methanol is a liquid, it is easier to store and transport than hydrogen gas, and is safer (it won't explode). Methanol also has a high energy density-a little goes a long way, making it especially interesting for portable devices. The DMFCs currently on the market, however, have limitations. For example, the material currently used for the electrolyte sandwiched between the electrodes is expensive. Even more important: that material, known as Nafion, is permeable to methanol, allowing some of the fuel to seep across the center of the fuel cell. Among other disadvantages, this wastes fuel-and lowers the efficiency of the cell-because the fuel isn't available for the reactions that generate electricity. i Using a relatively new technique known as layer-by-layer assembly, the MIT researchers created an alternative to Nafion. “We were able to tune the structure of [our] film a few nanometers at a time,” Hammond said, getting around some of the problems associated with other approaches. The result is a thin film that is two orders of magnitude less permeable to methanol but compares favorably to Nafion in proton conductivity. To test their creation, the engineers coated a Nafion membrane with the new film and incorporated the whole into a direct methanol fuel cell. The result was an increase in power output of more than 50 percent. The team is now exploring whether the new film could be used by itself, completely replacing Nafion. To that end, they have been generating thin films that stand alone, with a consistency much like plastic wrap. This work was supported by the DuPont-MIT Alliance through 2007. It is currently supported by the National Science Foundation. （Source: http://physorg.com/） [ Last edited by ddx-k on 2008-12-4 at 20:07 ] |
回复此楼» 猜你喜欢
317分 一志愿南理工材料工程 本科湖工大 求调剂
已经有11人回复
-
332求调剂
已经有12人回复
-
材料专硕 085600求调剂
已经有5人回复
-
0703化学/290求调剂/本科经历丰富/工科也可
已经有14人回复
-
283求调剂（080500）
已经有14人回复
-
材料工程专硕求调剂
已经有6人回复
-
材料专硕调剂
已经有9人回复
-
求调剂 有机化学考研356分
已经有11人回复
-
环境科学与工程334分求调剂
已经有8人回复
-
考研调剂
已经有5人回复
» 本主题相关商家推荐: (我也要在这里推广)
10