| 查看: 746 | 回复: 4 | |||
| 当前主题已经存档。 | |||
huaxingjin木虫 (著名写手)
|
[交流]
请教：MS中DPD模块的重新计算的问题
|
||
|
请教： 运行DPD模块，如果运行了1000步，结束后，想继续运行下1000步，怎么办？ 是要重新setup中，设定2000嘛？有办法让他在1000步基础上继续运算嘛？ 请高手指点，非常感谢！ [ Last edited by zzgyb on 2007-12-3 at 20:22 ] |
回复此楼» 猜你喜欢
今年E04面上
已经有20人回复
-
网络举报学术不端成为了男女之间情杀的手段了，真荒唐。。。
已经有3人回复
-
大龄残疾硕士的一点执念
已经有20人回复
-
2026年面上项目中了，2A+B, 会评顺利通过
已经有12人回复
-
Suzuki偶联中硼酸酯原料掉下的硼酸酯是否可以自身偶联，生成B2Pin2杂质
已经有3人回复
-
刑法学论文投稿求助
已经有5人回复
-
Journal of Environmental Chemical Engineering
已经有3人回复
-
最后一年，祈求好运
已经有3人回复
-
风电环氧领域
已经有3人回复
zzgyb
荣誉版主 (文坛精英)
小木虫警察局局长
- 应助: 0 (幼儿园)
- 贵宾: 22.58
- 金币: 42798.1
- 红花: 19
- 帖子: 10334
- 在线: 199.3小时
- 虫号: 136380
- 注册: 2005-12-16
- 性别: GG
- 专业: 催化化学
- 管辖: 竞技体育
2楼2007-11-13 09:00:54
huaxingjin
木虫 (著名写手)
- 应助: 0 (幼儿园)
- 金币: 4322.5
- 帖子: 1416
- 在线: 261.2小时
- 虫号: 221936
- 注册: 2006-03-20
- 性别: GG
- 专业: 药剂学
3楼2007-11-13 12:30:38
zzgyb
荣誉版主 (文坛精英)
小木虫警察局局长
- 应助: 0 (幼儿园)
- 贵宾: 22.58
- 金币: 42798.1
- 红花: 19
- 帖子: 10334
- 在线: 199.3小时
- 虫号: 136380
- 注册: 2005-12-16
- 性别: GG
- 专业: 催化化学
- 管辖: 竞技体育
★ ★ ★ ★
vzhang77(金币+4,VIP+0):多谢继续关注！：）
vzhang77(金币+4,VIP+0):多谢继续关注！：）
|
Restarting a DPD run At the end of a DPD run and at specified intervals during the run, DPD saves a restart data file, .Dpd_rst. This file is downloaded at the end of the run and contains the positions and velocities of all the beads. It enables you to restart the simulation from part way through or at the end of the previous DPD run. To restart a simulation 1. Select the mesoscale trajectory document from the run you wish to restart. 2. Choose Modules | DPD | Calculation from the menu bar. 3. Load the parameters from the run you wish to restart, by double-clicking on the associated Settings file in the Project Explorer. 4. Check Restart. 5. On the Setup tab, choose whether to Reinitialize averages. 6. Change the length of the run. Note. The time step counter is not reset between simulations. Therefore, the restarted DPD simulation will run for the Number of steps specified on the Setup tab less the number of steps already completed. 7. If desired, specify new output options, simulation conditions and interaction parameters. 8. Press Run. Note. The Restart checkbox is enabled only if a restart file is present. However, this file cannot be seen in the Project Explorer window. You can use the Windows Explorer to verify that the file exists. Note. When you restart a simulation you can modify some parameters such as the length of the run, output period options, simulation conditions, interaction parameters, etc. However, others, such as simulation cell size, grid spacing, cell contents, etc., must remain the same as they were before the restart. These options are disabled when Restart is checked. |
4楼2007-11-13 15:01:38
5楼2007-12-18 22:45:06