| 查看: 2197 | 回复: 2 | |||
datou_nono银虫 (小有名气)
|
[求助]
NASA battery capacity data set 分析
|
|
有没有使用过NASA battery capacity data set的啊，如下给出Li-ion batteries (# 5, 6, 7 and 18)的数据及测试条件。对于这样的mat文件，怎么得到横轴为充放电次数，纵轴为电池容量的数据呢？ 谢谢大家的帮助啊！ Data Description: A set of four Li-ion batteries (# 5, 6, 7 and 18) were run through 3 different operational profiles (charge, discharge and impedance) at room temperature. Charging was carried out in a constant current (CC) mode at 1.5A until the battery voltage reached 4.2V and then continued in a constant voltage (CV) mode until the charge current dropped to 20mA. Discharge was carried out at a constant current (CC) level of 2A until the battery voltage fell to 2.7V, 2.5V, 2.2V and 2.5V for batteries 5 6 7 and 18 respectively. Impedance measurement was carried out through an electrochemical impedance spectroscopy (EIS) frequency sweep from 0.1Hz to 5kHz. Repeated charge and discharge cycles result in accelerated aging of the batteries while impedance measurements provide insight into the internal battery parameters that change as aging progresses. The experiments were stopped when the batteries reached end-of-life (EOL) criteria, which was a 30% fade in rated capacity (from 2Ahr to 1.4Ahr). This dataset can be used for the prediction of both remaining charge (for a given discharge cycle) and remaining useful life (RUL). Files: B0005.mat Data for Battery #5 B0006.mat Data for Battery #6 B0007.mat Data for Battery #7 B0018.mat Data for Battery #18 Data Structure: cycle: top level structure array containing the charge, discharge and impedance operations type: operation type, can be charge, discharge or impedance ambient_temperature: ambient temperature (degree C) time: the date and time of the start of the cycle, in MATLAB date vector format data: data structure containing the measurements for charge the fields are: Voltage_measured: Battery terminal voltage (Volts) Current_measured: Battery output current (Amps) Temperature_measured: Battery temperature (degree C) Current_charge: Current measured at charger (Amps) Voltage_charge: Voltage measured at charger (Volts) Time: Time vector for the cycle (secs) for discharge the fields are: Voltage_measured: Battery terminal voltage (Volts) Current_measured: Battery output current (Amps) Temperature_measured: Battery temperature (degree C) Current_charge: Current measured at load (Amps) Voltage_charge: Voltage measured at load (Volts) Time: Time vector for the cycle (secs) Capacity: Battery capacity (Ahr) for discharge till 2.7V for impedance the fields are: Sense_current: Current in sense branch (Amps) Battery_current: Current in battery branch (Amps) Current_ratio: Ratio of the above currents Battery_impedance: Battery impedance (Ohms) computed from raw data Rectified_impedance: Calibrated and smoothed battery impedance (Ohms) Re: Estimated electrolyte resistance (Ohms) Rct: Estimated charge transfer resistance (Ohms) |
回复此楼» 猜你喜欢
广西师范大学化学与药学学院杨秀林课题组2026年拟招收博士研究生1名
已经有25人回复
-
26年储能、电池方向博士申请
已经有1人回复
-
分析化学论文润色/翻译怎么收费?
已经有287人回复
-
求调剂，本科吉大，一志愿华工339
已经有2人回复
-
意大利博洛尼亚大学招聘研究助理2名（2D材料/锂离子与钠离子电池方向）
已经有1人回复
-
关于碳量子点抗菌的研究
已经有15人回复
-
南大化学调剂
已经有11人回复
-
硫酸钠溶液浓度与密度曲线
已经有0人回复
-
0703调剂
已经有2人回复
-
请教各位大佬，锌空电池电解液该投哪个口合适？
已经有11人回复
-
0703 调剂
已经有2人回复
» 本主题相关价值贴推荐，对您同样有帮助:
2楼2019-02-27 16:19:04
皮肤嘿嘿
金虫 (小有名气)
- 应助: 0 (幼儿园)
- 金币: 1187.6
- 散金: 276
- 帖子: 206
- 在线: 87.5小时
- 虫号: 2414304
- 注册: 2013-04-12
- 性别: GG
- 专业: 机械测试理论与技术
|
%使用MATLAB导入电池数据，在cycle中筛选要计算的目标，容量在discharge中提取，那么放电一次就充放电一次，提取多少Capacit%y就循环多少次，也可以对应时间轴，不过时间轴作用不大，因为长时间的涓流充电意义不大。给你部分MATLAB代码吧： clear clc load B0005 load B0006 load B0007 load B0018 j=1; type_name='discharge'; for i=1:length(B0005.cycle) % 5、6、7号电池数据长度相同 cycle_05=B0005.cycle(i); cycle_06=B0006.cycle(i); cycle_07=B0007.cycle(i); if strcmp(cycle_05.type,type_name)==0 continue else cap_05(j,  =cycle_05.data.Capacity;end |
3楼2021-02-19 22:46:40
