| 查看: 1531 | 回复: 1 | |||
[交流]
ANSYS热分析加载荷出错，请问到底是什么原因
|
|
各位，我用ANSYS仿真生死单元，建模加初始温度载荷稳态分析的时候老出错，请各位给我看看怎么回事： 错误一：Specified degree of freedom constraint TEMP at unused node 7331. 错误2： Material property DENS of material 1 of element 5 is evaluated at a temperature of 0, which is below the supplied temperature range. Temperature range checking terminates. 错误3：There are no active degrees of freedom. 错误4：A reference heat flow value times the tolerance is used by the Newton-Raphson method for checking convergence. The calculated reference HT FLOW CONVERGENCE VALUE= 2.970385058E-14 is less than a threshold. This threshold defaults to 1.0e-6 or is specified as MINREF on the CNVTOL command. Check results carefully. 能解决几个是几个，谢谢各位大神！！！！！！！ 命令流： /prep7 et,1,plane77 et,2,solid70 mptemp,1,25,90,160 mpdata,dens,1,1,8500,8500,8500 mpdata,dens,2,1,1150,1150,1150 mpdata,c,1,1,380,380,380 mpdata,c,2,1,1470,1470,1470 mpdata,kxx,1,1,130,130,130 mpdata,kxx,2,1,0.03,0.03,0.03 rect,0,0.1,0,0.1 asel,s,area,,1 aatt,1 esize,0.004 mshkey,1 mshape,0 amesh,1 extopt,esize,5 extopt,aclear,1 extopt,attr,1,1,1 mat,1 vext,1,,,,,-0.02 rect,0.03,0.07,0.03,0.07 asel,s,area,,7 aatt,2 esize,0.004 mshkey,1 mshape,0 amesh,7 mat,2 vext,7,,,,,0.02 allsel finish /prep7 et,1,plane77 et,2,solid70 mptemp,1,25,90,160 mpdata,dens,1,1,8500,8500,8500 mpdata,dens,2,1,1150,1150,1150 mpdata,c,1,1,380,380,380 mpdata,c,2,1,1470,1470,1470 mpdata,kxx,1,1,130,130,130 mpdata,kxx,2,1,0.03,0.03,0.03 rect,0,0.1,0,0.1 asel,s,area,,1 aatt,1 esize,0.004 mshkey,1 mshape,0 amesh,1 extopt,esize,5 extopt,aclear,1 extopt,attr,1,1,1 mat,1 vext,1,,,,,-0.02 rect,0.03,0.07,0.03,0.07 asel,s,area,,7 aatt,2 esize,0.004 mshkey,1 mshape,0 amesh,7 mat,2 vext,7,,,,,0.02 allsel finish |
回复此楼» 猜你喜欢
售一区SCI文章T0P，我:8O.551.O54,科目全,可十急
已经有7人回复
-
售一区SCI文章T0P，我:8O.551.O54,科目全,可十急
已经有7人回复
-
售SCI一区文章，我:8O5.5.1.O5.4,科目全,可伽急
已经有8人回复
-
售SCI一区T0P文章，我:8.O.55.1.O.5.4,科目全,可+急
已经有15人回复
-
售SCI文章，我:8O.5.5.1O.54,科目全,可十急
已经有13人回复
-
售SCI一区T0P文章，我:8.O.55.1.O.54,科目齐全,可+急
已经有18人回复
-
售SCI-T0P文章，我:8O.5.5.1.O.54,科目齐全,可+急
已经有13人回复
-
售SCI文章，我:8O.5.5.1O.54,科目全,可十急
已经有14人回复
-
售SCI-T0P文章，我:8O.5.5.1.O.54,科目齐全,可+急
已经有22人回复
-
售SCI一区T0P文章，我:8.O.55.1.O.5.4,科目全,可+急
已经有22人回复
2楼2018-09-11 11:02:07
50