| 查看: 4195 | 回复: 3 | ||
[求助]
求大神帮忙：ANSYS模拟钢筋混凝土板并考虑粘结滑移，无法求解（附命令流）
|
|
建模是利用分离式建模并在钢筋混凝土间施加弹簧单元，但在这一块理解不到位很可能出错了。 求解出现的警告和错误主要是说约束不足和出现大位移。 *** WARNING *** CP = 54.141 TIME= 17:41:19 There is at least 1 small equation solver pivot term (e.g., at the UZ degree of freedom of node 1) which may indicate a numerically unstable model. Please check your results carefully. *** WARNING *** CP = 61.250 TIME= 17:41:23 An extremely large pivot ratio has been detected by the sparse solver. This usually indicates a very ill-conditioned matrix or possibly rigid-body motion. The solution may be inaccurate or even erroneous. Please check your results carefully. *** ERROR *** CP = 61.391 TIME= 17:41:23 The value of UZ at node 238 is 1.695793158E+23. It is greater than the current limit of 1000000 (which can be reset on the NCNV command). This generally indicates rigid body motion as a result of an unconstrained model. Verify that your model is properly constrained. *** WARNING *** SUPPRESSED MESSAGE CP = 163.281 TIME= 17:42:23 The unconverged solution (identified as time 1 substep 999999) is output for analysis debug purposes. Results should not be used for any other purpose. |
回复此楼» 猜你喜欢
售SCI一区T0P文章，我:8O.55.1.O.5.4,科目齐全,可+急
已经有5人回复
-
售SCI一区T0P文章，我:8.O55.1.O.54,科目全,可十急
已经有6人回复
-
售一区SCI文章T0P，我:8O.551.O54,科目全,可十急
已经有7人回复
-
售SCI一区T0P文章，我:8.O.55.1.O54,科目全,可伽急
已经有6人回复
-
售SCI一区文章，我:8.O.551.O.5.4,科目全,可伽急
已经有10人回复
-
售SCI一区T0P文章，我:8.O55.1.O.54,科目全,可十急
已经有8人回复
-
售SCI一区文章，我:8.O.55.1.O.54,科目齐全,可伽急
已经有9人回复
-
售SCI一区文章，我:8.O.55.1.O.54,科目齐全,可伽急
已经有5人回复
-
售SCI文章，我:8O5.5.1.O.54,科目齐全,可+急
已经有8人回复
-
售SCI一区文章，我:8O5.5.1.O5.4,科目全,可伽急
已经有13人回复
|
本帖内容被屏蔽 |
2楼2017-02-26 16:43:25
study虫
新虫 (小有名气)
- 应助: 0 (幼儿园)
- 金币: 426.2
- 散金: 30
- 帖子: 107
- 在线: 44.6小时
- 虫号: 6309657
- 注册: 2017-04-13
- 性别: MM
- 专业: 结构工程
3楼2017-06-06 15:54:40
4楼2019-04-09 17:19:53
