| 查看: 1765 | 回复: 8 | |||||
| 当前只显示满足指定条件的回帖，点击这里查看本话题的所有回帖 | |||||
[求助]
急求DPM边界条件为wall flim的算例 已有1人参与
|
|||||
| 急求DPM边界条件为wall flim的算例，谢谢啊~ 目前使用fluent14.5，做两相流离散相模拟 |
回复此楼» 猜你喜欢
FileCode能看出啥？
已经有23人回复
-
应该是93bebmhtak前后十一个字符比较关键
已经有36人回复
-
关于Filecode分析方法
已经有9人回复
-
2019年青年基金涵评意见，大家看看几个A，几个B?
已经有10人回复
-
不应该看fileCode
已经有6人回复
-
好奇怪的filecode
已经有6人回复
-
长年满屏的广告，版主太不责任了。基金也等的急
已经有4人回复
-
filecode
已经有15人回复
-
职称评审，求友友推荐见刊最快的期刊
已经有4人回复
-
奇怪，两个人的filecode固定段从头到尾一模一样
已经有10人回复
dai26520
专家顾问 (著名写手)
-
专家经验: +219 - 仿真EPI: 1
- 应助: 224 (大学生)
- 金币: 4097
- 散金: 4143
- 红花: 107
- 帖子: 1850
- 在线: 529.6小时
- 虫号: 1619980
- 注册: 2012-02-16
- 专业: 高分子合成化学
- 管辖: 仿真模拟
【答案】应助回帖
|
百度一下这个官方算例：Modeling of Film Separation at Backward Facing Step 1. Introduction Backward facing step is a widely used benchmark problem to evaluate the performance of turbulence models for the prediction of separated flows & reattachment. In this tutorial the backward facing step problem is used to demonstrate the use of Eulerian Wall Film (EWF) model for predicting the separation of liquid film. The EWF model can be used to predict the formation and flow of thin liquid films on wall surfaces. This model can be used with: • Discrete Phase Model – Particles are collected on the wall to form the film. • Eulerian Multiphase Model – Secondary phase mass is collected on the wall to form the film. In EWF model, the film is not resolved using mesh normal to the surface, instead this model uses a vir- tual film on the surface. In many cases you would be interested in modeling a thin film flow which can separate, strip and evaporate but does not affect the core flow-field. In general multiphase frame work, this thin film modeling is computationally expensive because a very fine mesh is required near the surface to resolve the film and the inter-phase flux needs to be calculated accurately. EWF model can only be used with 3D solver and EWF model assumes that film always flows parallel to the surface so normal component of film velocity is zero. The film is assumed to have a parabolic velocity profile & bilinear temperature profile across its depth. In this tutorial you will learn to: • Couple EWF model with Discrete Phase Model to create film. • Model detachment of film at edge. • Model film heat transfer. |
7楼2016-03-14 09:01:07
3楼2016-03-07 10:26:32
MichaelLaw
新虫 (初入文坛)
- 应助: 1 (幼儿园)
- 金币: 282.8
- 散金: 5
- 红花: 1
- 帖子: 18
- 在线: 12.5小时
- 虫号: 3764366
- 注册: 2015-03-25
- 性别: GG
- 专业: 内流流体力学
4楼2016-03-13 23:41:06
dai26520
专家顾问 (著名写手)
-
专家经验: +219 - 仿真EPI: 1
- 应助: 224 (大学生)
- 金币: 4097
- 散金: 4143
- 红花: 107
- 帖子: 1850
- 在线: 529.6小时
- 虫号: 1619980
- 注册: 2012-02-16
- 专业: 高分子合成化学
- 管辖: 仿真模拟
【答案】应助回帖
|
百度一下这个官方算例：Modeling of Film Separation at Backward Facing Step 1. Introduction Backward facing step is a widely used benchmark problem to evaluate the performance of turbulence models for the prediction of separated flows & reattachment. In this tutorial the backward facing step problem is used to demonstrate the use of Eulerian Wall Film (EWF) model for predicting the separation of liquid film. The EWF model can be used to predict the formation and flow of thin liquid films on wall surfaces. This model can be used with: • Discrete Phase Model – Particles are collected on the wall to form the film. • Eulerian Multiphase Model – Secondary phase mass is collected on the wall to form the film. In EWF model, the film is not resolved using mesh normal to the surface, instead this model uses a vir- tual film on the surface. In many cases you would be interested in modeling a thin film flow which can separate, strip and evaporate but does not affect the core flow-field. In general multiphase frame work, this thin film modeling is computationally expensive because a very fine mesh is required near the surface to resolve the film and the inter-phase flux needs to be calculated accurately. EWF model can only be used with 3D solver and EWF model assumes that film always flows parallel to the surface so normal component of film velocity is zero. The film is assumed to have a parabolic velocity profile & bilinear temperature profile across its depth. In this tutorial you will learn to: • Couple EWF model with Discrete Phase Model to create film. • Model detachment of film at edge. • Model film heat transfer. |
5楼2016-03-14 09:00:53
