| ²é¿´: 9552 | »Ø¸´: 4 | |||
markxfгæ (³õÈëÎÄ̳)
|
[ÇóÖú]
CFX¸ßÂíºÕÊý¶¨³£Çó½â³ö´í£¬ÓйØT+ clip value value ÒÑÓÐ1È˲ÎÓë
|
|
ÓÃCFXÄ£ÄⳬÉùËÙÁ÷£¨ÍÄÁ÷Ä£ÐÍSST£©£¬¾¯¸æ£ºthe non-dimensional near wall temperature (T+) has been clipped for calculation of wall heat transfer coefficient¡£ »¹ÓÐÌáʾ£ºIf this situation persists and you are using the high speed model,consider enabling mach number based blending between low speed and high speed wall functons. You can do so by specifying a mach number threshold as follows: EXPERT PARAMETERS: highspeed wf mach threshold = 0.1 #default=0.0(off)¡£ È»ºó¾Í³öÏÖ Fatal overflow in linear solver´íÎó£¬ÖÕÖ¹¼ÆËã¡£ ÓÃma6¼ÆË㣬1000¶à²½ºó³öÏÖÕâ¸öÌáʾ£¬ÓÃma8¼ÆË㣬ǰ¼¸²½¾Í»á³öÏÖÕâ¸öÌáʾ¡£ 1.ÇëÎÊÊÇʲôÔÒòµ¼ÖÂÉÏÊö´íÎ󣬸ÃÈçºÎ½â¾ö£¿ 2.ÌáʾÖÐÌáµ½µÄhighspeed wf mach threshold£¬ÔÚEXPERT PARAMETERSÖÐÕÒ²»µ½highspeed wf mach thresholdÑ¡ÏÓÃCCLÃüÁî°Ñhighspeed wf mach threshold = 0.1Õâ¸öÃüÁî¼ÓÈ룬·¢ÏÖ¼ÆËãÏàͬ£¬»¹ÊÇÌáʾÌí¼Óhighspeed wf mach threshold = 0.1£¬ÇëÎÊhighspeed wf mach thresholdÔÚÄÄÀï¿ÉÒÔÖ¸¶¨£¿ |
» ²ÂÄãϲ»¶
ѰÕÒµ÷¼Á
ÒѾÓÐ8È˻ظ´
289Çóµ÷¼Á
ÒѾÓÐ16È˻ظ´
312Çóµ÷¼Á
ÒѾÓÐ8È˻ظ´
263Çóµ÷¼Á
ÒѾÓÐ10È˻ظ´
Ò»Ö¾Ô¸C9²ÄÁÏÓ뻯¹¤×¨Òµ×Ü·Ö300Çóµ÷¼Á
ÒѾÓÐ6È˻ظ´
296Çóµ÷¼Á
ÒѾÓÐ5È˻ظ´
0703»¯Ñ§/290Çóµ÷¼Á/±¾¿Æ¾Àú·á¸»/¹¤¿ÆÒ²¿É
ÒѾÓÐ5È˻ظ´
284Çóµ÷¼Á
ÒѾÓÐ4È˻ظ´
»¯Ñ§¹¤³Ì085602 305·ÖÇóµ÷¼Á
ÒѾÓÐ12È˻ظ´
¿¼Ñе÷¼Á
ÒѾÓÐ4È˻ظ´
°¢Áº110
гæ (³õÈëÎÄ̳)
- Ó¦Öú: 0 (Ó×¶ùÔ°)
- ½ð±Ò: 13
- Ìû×Ó: 2
- ÔÚÏß: 17·ÖÖÓ
- ³æºÅ: 6139399
- ×¢²á: 2017-03-25
- רҵ: Á÷ÌåÁ¦Ñ§
|
Äã×¢Òâһϣ¬Á÷¹Ì½»½çÃæÊÇ·ñºÜºÃµÄ¶ÔÓ¦£¬ÔÚǰ´¦ÀíinterfaceÄÇÀï¿´¿´ ·¢×ÔСľ³æAndroid¿Í»§¶Ë |
2Â¥2018-04-26 11:17:30
1210314836
гæ (³õÈëÎÄ̳)
- Ó¦Öú: 0 (Ó×¶ùÔ°)
- ½ð±Ò: 4.5
- Ìû×Ó: 21
- ÔÚÏß: 15.3Сʱ
- ³æºÅ: 8629762
- ×¢²á: 2018-04-26
- רҵ: Á÷ÌåÁ¦Ñ§
3Â¥2018-10-31 09:44:35
pingan04507
гæ (СÓÐÃûÆø)
- Ó¦Öú: 0 (Ó×¶ùÔ°)
- ½ð±Ò: 514.8
- Ìû×Ó: 121
- ÔÚÏß: 33Сʱ
- ³æºÅ: 2242485
- ×¢²á: 2013-01-15
- רҵ: ¿ÉÔÙÉúÓëÌæ´úÄÜÔ´ÀûÓÃÖеÄ
4Â¥2019-04-24 19:56:33
|
±¾ÌûÄÚÈݱ»ÆÁ±Î |
5Â¥2024-12-25 17:20:15













»Ø¸´´ËÂ¥