| 查看: 412 | 回复: 3 | |||
| 当前主题已经存档。 | |||
| 当前只显示满足指定条件的回帖，点击这里查看本话题的所有回帖 | |||
[交流]
求助关于Caco-2的教材
|
|||
|
本人在进行Caco-2细胞模型实验时遇到很多疑难问题，请各位小虫，大虫，青虫们帮助一下，给我推荐一份关于Caco-2细胞模型的教材，让我解惑。 在此谢过了！   |
回复此楼» 猜你喜欢
334分 一志愿武理-080500 材料求调剂
已经有10人回复
-
324分 085600材料与化工
已经有7人回复
-
各位老师好，我的一志愿为北京科技大学085601材料专硕
已经有11人回复
-
309求调剂
已经有6人回复
-
调剂推荐
已经有7人回复
-
一志愿西交大080500材料学硕349
已经有7人回复
-
一志愿北京科技大学085601材料工程英一数二初试总分335求调剂
已经有4人回复
-
352分-085602-一志愿985
已经有6人回复
-
273求调剂
已经有5人回复
-
349求调剂
已经有4人回复
以下是current protocol in pharmacology中的步骤，没法贴附件，可通过邮件发给您！
★
小木虫(金币+0.5):给个红包，谢谢回帖交流
小木虫(金币+0.5):给个红包，谢谢回帖交流
|
1. Serially dilute the 1.0 mM L-carnosine (or other test compound) with HBSS to prepare 200 μl each of five solutions at 100, 10, 5, 2.5, and 1 μM. 2. Add 100 μl of 0.05 N HCl to each standard solution. 3. Using a Pasteur pipet connected to a vacuum pump, aspirate the medium from both the apical (donor) and basolateral (receiver) sides of three Transwells of cells grown for 21 to 28 days. Wash the cell monolayers by adding 1.5 ml and 2.6 ml of 37°C HBSS to the apical and basolateral compartments, respectively, and then aspirating the HBSS from both compartments. Repeat. 4. Add fresh 1.5-ml and 2.6-ml aliquots of HBSS to the Transwells and incubate 30 min in a shaking water bath (37°C, 55 rpm). 5. Aspirate HBSS from both sides and add 2.6 ml of 37°C HBSS to the receiver side. Add 1.5 ml of 1.0 mM L-carnosine at 37°C to the donor side. Place the Transwells in the shaking water bath. 6. Remove 20-μl samples from the donor side at 0, 60, and 120 min, and mix each with 280 μl of 0.01 N HCl. Remove 200-μl samples from the receiver side at 15, 30, 45, 60, 90, and 120 min, and mix each with 100 μl of 0.05 N HCl. Replenish the receiver side with the same volume (200 μl) of 37°C HBSS after each sampling. 7. Determine the amount of test compound in the transport experiment samples and the standards (step 2) by HPLC (injection volume = 140 μl). Prepare a standard curve and determine the concentrations of the samples from the transport experiment by comparing their peak areas with those obtained from the standard curve. 8. Plot concentration versus time for the samples from the donor side. 9. Calculate the cumulative amount, Q (in mmol), of L-carnosine transported to the receiver side at each time point using the concentration data from step 7. In the calculations, take into account the dilution of the receiver solution (i.e., at each sampling, 200 μl solution was removed and 200 μl fresh buffer was replenished). 10. Plot the cumulative amount transported (Q) versus time (see Fig. 7.2.2) and determine the linear appearance rate (slope = ΔQ/Δt) of L-carnosine on the receiver side. 11. Calculate the Papp (in cm/sec) according to the following equation: Papp = (ΔQ/Δt)/(ACo), where ΔQ/Δt is the linear appearance rate of the compound on the receiver side (in mmol/sec) determined in the last step (convert the time unit accordingly); A is the surface area of the cell monolayers (in cm2; 4.71 cm2 for Transwells 24 mm in diameter); and C0 is the initial concentration of the compound on the donor side (in mmol/cm3). See Table 7.2.1 for original data and calculated results; see Anticipated Results for interpretation of the results. |
4楼2009-07-17 16:59:35
2楼2009-07-17 16:20:18
3楼2009-07-17 16:52:21
